|
|
We help Organizations quickly Conceptualize, Design, Develop, and Implement Innovative Cost-Effective Solutions for Avionics, Aircraft, and Flight Guidance-Navigation-Control Systems. |
|---|---|
|
|
|
Home
YOU
US
What
We Can
Do
What
We Have
Done -
On
Learjets
Why
ASTECH
ASTECH's
Founder
Expert's
Corner-
FAA FAR Part 25 C
Links
In
Closing
|
Subpart C--Structure 25.301 Loads. 25.321 General. Flight Maneuver and Gust Conditions 25.331 Symmetric maneuvering conditions. 25.361 Engine torque. Control Surface and System Loads 25.391 Control surface loads; general. 25.471 General. 25.521 General. 25.561 General. 25.571 Damage--tolerance and fatigue evaluation of structure. Lightning Protection Sec. 25.581 Lightning protection |
|
(a) Strength requirements are specified in terms of limit loads (the maximum loads to be expected in service) and ultimate loads (limit loads multiplied by prescribed factors of safety). Unless otherwise provided, prescribed loads are limit loads. (b) Unless otherwise provided, the specified air, ground, and water loads must be placed in equilibrium with inertia forces, considering each item of mass in the airplane. These loads must be distributed to conservatively approximate or closely represent actual conditions. Methods used to determine load intensities and distribution must be validated by flight load measurement unless the methods used for determining those loading conditions are shown to be reliable. (c) If deflections under load would significantly change the distribution of external or internal loads, this redistribution must be taken into account. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970] Sec. 25.303 Factor of safety. Unless otherwise specified, a factor of safety of 1.5 must be applied to the prescribed limit load which are considered external loads on the structure. When a loading condition is prescribed in terms of ultimate loads, a factor of safety need not be applied unless otherwise specified. [Amdt. 25-23, 35 FR 5672, Apr. 8, 1970] Sec. 25.305 Strength and deformation. (a) The structure must be able to support limit loads without detrimental permanent deformation. At any load up to limit loads, the deformation may not interfere with safe operation. (b) The structure must be able to support ultimate loads without failure for at least 3 seconds. However, when proof of strength is shown by dynamic tests simulating actual load conditions, the 3-second limit does not apply. Static tests conducted to ultimate load must include the ultimate deflections and ultimate deformation induced by the loading. When analytical methods are used to show compliance with the ultimate load strength requirements, it must be shown that-- (1) The effects of deformation are not significant; (2) The deformations involved are fully accounted for in the analysis; or (3) The methods and assumptions used are sufficient to cover the effects of these deformations. (c) Where structural flexibility is such that any rate of load application likely to occur in the operating conditions might produce transient stresses appreciably higher than those corresponding to static loads, the effects of this rate of application must be considered. (d) [Reserved] (e) The airplane must be designed to withstand any vibration and buffeting that might occur in any likely operating condition up to VD/MD, including stall and probable inadvertent excursions beyond the boundaries of the buffet onset envelope. This must be shown by analysis, flight tests, or other tests found necessary by the Administrator. (f) Unless shown to be extremely improbable, the airplane must be designed to withstand any forced structural vibration resulting from any failure, malfunction or adverse condition in the flight control system. These must be considered limit loads and must be investigated at airspeeds up to VC/MC. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-54, 45 FR 60172, Sept. 11, 1980; Amdt. 25-77, 57 FR 28949, June 29, 1992; Amdt. 25-86, 61 FR 5220, Feb. 9, 1996] Sec. 25.307 Proof of structure. (a) Compliance with the strength and deformation requirements of this subpart must be shown for each critical loading condition. Structural analysis may be used only if the structure conforms to that for which experience has shown this method to be reliable. The Administrator may require ultimate load tests in cases where limit load tests may be inadequate. (b) [Reserved] (c) [Reserved] (d) When static or dynamic tests are used to show compliance with the requirements of Sec. 25.305(b) for flight structures, appropriate material correction factors must be applied to the test results, unless the structure, or part thereof, being tested has features such that a number of elements contribute to the total strength of the structure and the failure of one element results in the redistribution of the load through alternate load paths. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as
amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt.
25-54, 45 FR 60172, Sept. 11, 1980; Amdt. 25-72, 55 FR
29775, July 20, 1990] |
|
|
(a) Flight load factors represent the ratio of the aerodynamic force component (acting normal to the assumed longitudinal axis of the airplane) to the weight of the airplane. A positive load factor is one in which the aerodynamic force acts upward with respect to the airplane. (b) Considering compressibility effects at each speed, compliance with the flight load requirements of this subpart must be shown-- (1) At each critical altitude within the range of altitudes selected by the applicant; (2) At each weight from the design minimum weight to the design maximum weight appropriate to each particular flight load condition; and (3) For each required altitude and weight, for any practicable distribution of disposable load within the operating limitations recorded in the Airplane Flight Manual. (c) Enough points on and within the boundaries of the design envelope must be investigated to ensure that the maximum load for each part of the airplane structure is obtained. (d) The significant forces acting on the airplane must be placed in equilibrium in a rational or conservative manner. The linear inertia forces must be considered in equilibrium with the thrust and all aerodynamic loads, while the angular (pitching) inertia forces must be considered in equilibrium with thrust and all aerodynamic moments, including moments due to loads on components such as tail surfaces and nacelles. Critical thrust values in the range from zero to maximum continuous thrust must be considered. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as
amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt.
25-86, 61 FR 5220, Feb. 9, 1996] |
|
|
(a) Procedure. For the analysis of the maneuvering flight conditions specified in paragraphs (b) and (c) of this section, the following provisions apply: (1) Where sudden displacement of a control is specified, the assumed rate of control surface displacement may not be less than the rate that could be applied by the pilot through the control system. (2) In determining elevator angles and chordwise load distribution in the maneuvering conditions of paragraphs (b) and (c) of this section, the effect of corresponding pitching velocities must be taken into account. The in-trim and out-of-trim flight conditions specified in Sec. 25.255 must be considered. (b) Maneuvering balanced conditions. Assuming the airplane to be in equilibrium with zero pitching acceleration, the maneuvering conditions A through I on the maneuvering envelope in Sec. 25.333(b) must be investigated. (c) Maneuvering pitching conditions. The following conditions involving pitching acceleration must be investigated: (1) Maximum elevator displacement at VA. The airplane is assumed to be flying in steady level flight (point A1, Sec. 25.333(b)) and, except as limited by pilot effort in accordance with Sec. 25.397(b), the pitching control is suddenly moved to obtain extreme positive pitching acceleration (nose up). The dynamic response or, at the option of the applicant, the transient rigid body response of the airplane, must be taken into account in determining the tail load. Airplane loads which occur subsequent to the normal acceleration at the center of gravity exceeding the maximum positive limit maneuvering load factor, n, need not be considered. (2) Specified control displacement. A checked maneuver, based on a rational pitching control motion vs. time profile, must be established in which the design limit load factor specified in Sec. 25.337 will not be exceeded. Unless lesser values cannot be exceeded, the airplane response must result in pitching accelerations not less than the following: (i) A positive pitching acceleration (nose up) is assumed to be reached concurrently with the airplane load factor of 1.0 (Points A1 to D1, Sec. 25.333(b)). The positive acceleration must be equal to at least ??? 39n ----- (n-1.5), (Radians/sec./2/ )v where--n is the positive load factor at the speed under consideration, and V is the airplane equivalent speed in knots. (ii) A negative pitching acceleration (nose down) is assumed to be reached concurrently with the positive maneuvering load factor (Points A2 to D2, Sec. 25.333(b)). This negative pitching acceleration must be equal to at least ??? -26n ------ (n-1.5), (Radians/sec./2/ ) v where-- n is the positive load factor at the speed under consideration; and V is the airplane equivalent speed in knots. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-46, 43 FR 50594, Oct. 30, 1978; 43 FR 52495, Nov. 13, 1978; 43 FR 54082, Nov. 20, 1978; Amdt. 25-72, 55 FR 29775, July 20, 1990; 55 FR 37607, Sept. 12, 1990; Amdt. 25-86, 61 FR 5220, Feb. 9, 1996] Sec. 25.333 Flight maneuvering envelope. (a) General. The strength requirements must be met at each combination of airspeed and load factor on and within the boundaries of the representative maneuvering envelope (V-n diagram) of paragraph (b) of this section. This envelope must also be used in determining the airplane structural operating limitations as specified in Sec. 25.1501. (b) Maneuvering envelope. [ ...???Illustrations appears here... ] [Docet No. 5066, 29 FR 18291, Dec. 24, 1964, as amended at Amdt. 25-86, 61 FR 5220, Feb. 9, 1996] Sec. 25.335 Design airspeeds. The selected design airspeeds are equivalent airspeeds (EAS). Estimated values of VS0 and VS1 must be conservative. (a) Design cruising speed, VC. For VC, the following apply: (1) The minimum value of VC must be sufficiently greater than VB to provide for inadvertent speed increases likely to occur as a result of severe atmospheric turbulence. (2) In the absence of a rational investigation substantiating the use of other values, VC may not be less than VB+43 knots. However, it need not exceed the maximum speed in level flight at maximum continuous power for the corresponding altitude. (3) At altitudes where VD is limited by Mach number, VC may be limited to a selected Mach number. (b) Design dive speed, VD. VD must be selected so that VC/MC is not greater than 0.8 VD/MD, or so that the minimum speed margin between VC/MC and VD/MD is the greater of the following values: (1) From an initial condition of stabilized flight at VC/MC, the airplane is upset, flown for 20 seconds along a flight path 7.5 deg. below the initial path, and then pulled up at a load factor of 1.5 g (0.5 g acceleration increment). The speed increase occurring in this maneuver may be calculated if reliable or conservative aerodynamic data is used. Power as specified in Sec. 25.175(b)(1)(iv) is assumed until the pullup is initiated, at which time power reduction and the use of pilot controlled drag devices may be assumed; (2) The minimum speed margin must be enough to provide for atmospheric variations (such as horizontal gusts, and penetration of jet streams and cold fronts) and for instrument errors and airframe production variations. These factors may be considered on a probability basis. However, the margin at altitude where MC is limited by compressibility effects may not be less than 0.05 M. (c) Design maneuvering speed VA. For VA, the following apply: (1) VA may not be less than VS1 <radical>n where-- (i) n is the limit positive maneuvering load factor at VC; and (ii) VS1 is the stalling speed with flaps retracted. (2) VA and VS must be evaluated at the design weight and altitude under consideration. (3) VA need not be more than VC or the speed at which the positive CN max curve intersects the positive maneuver load factor line, whichever is less. (d) Design speed for maximum gust intensity, VB. (1) VB may not be less than [ ...Illustrations appears here... ] (2) At altitudes where VC is limited by Mach number-- (i) VB may be chosen to provide an optimum margin between low and high speed buffet boundaries; and, (ii) VB need not be greater than VC. (e) Design flap speeds, VF. For VF, the following apply: (1) The design flap speed for each flap position (established in accordance with Sec. 25.697(a)) must be sufficiently greater than the operating speed recommended for the corresponding stage of flight (including balked landings) to allow for probable variations in control of airspeed and for transition from one flap position to another. (2) If an automatic flap positioning or load limiting device is used, the speeds and corresponding flap positions programmed or allowed by the device may be used. (3) VF may not be less than-- (i) 1.6 VS1 with the flaps in takeoff position at maximum takeoff weight; (ii) 1.8 VS1 with the flaps in approach position at maximum landing weight, and (iii) 1.8 VS0 with the flaps in landing position at maximum landing weight. (f) Design drag device speeds, VDD. The selected design speed for each drag device must be sufficiently greater than the speed recommended for the operation of the device to allow for probable variations in speed control. For drag devices intended for use in high speed descents, VDD may not be less than VD. When an automatic drag device positioning or load limiting means is used, the speeds and corresponding drag device positions programmed or allowed by the automatic means must be used for design. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-86, 61 FR 5220, Feb. 9, 1996] Sec. 25.337 Limit maneuvering load factors. (a) Except where limited by maximum (static) lift coefficients, the airplane is assumed to be subjected to symmetrical maneuvers resulting in the limit maneuvering load factors prescribed in this section. Pitching velocities appropriate to the corresponding pull-up and steady turn maneuvers must be taken into account. (b) The positive limit maneuvering load factor "n" for any speed up to Vn may not be less than 2.1+24,000/ (W +10,000) except that "n" may not be less than 2.5 and need not be greater than 3.8--where "W" is the design maximum takeoff weight. (c) The negative limit maneuvering load factor-- (1) May not be less than -1.0 at speeds up to VC; and (2) Must vary linearly with speed from the value at VC to zero at VD. (d) Maneuvering load factors lower than those specified in this section may be used if the airplane has design features that make it impossible to exceed these values in flight. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970] Sec. 25.341 Gust and turbulence loads. (a) Discrete Gust Design Criteria. The airplane is assumed to be subjected to symmetrical vertical and lateral gusts in level flight. Limit gust loads must be determined in accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic analysis. The analysis must take into account unsteady aerodynamic characteristics and all significant structural degrees of freedom including rigid body motions. (2) The shape of the gust must be: [ ...Illustration appears here... ] (3) A sufficient number of gust gradient distances in the range 30 feet to 350 feet must be investigated to find the critical response for each load quantity. (4) The design gust velocity must be: [ ...Illustration appears here... ] (5) The following reference gust velocities apply: (i) At the airplane design speed VC: Positive and negative gusts with reference gust velocities of 56.0 ft/sec EAS must be considered at sea level. The reference gust velocity may be reduced linearly from 56.0 ft/sec EAS at sea level to 44.0 ft/sec EAS at 15000 feet. The reference gust velocity may be further reduced linearly from 44.0 ft/sec EAS at 15000 feet to 26.0 ft/sec EAS at 50000 feet. (ii) At the airplane design speed VD: The reference gust velocity must be 0.5 times the value obtained under Sec. 25.341(a)(5)(i). (6) The flight profile alleviation factor, Fg, must be increased linearly from the sea level value to a value of 1.0 at the maximum operating altitude defined in Sec. 25.1527. At sea level, the flight profile alleviation factor is determined by the following equation: [ ...Illustration appears here... ] Zmo=Maximum operating altitude defined in Sec. 25.1527. (7) When a stability augmentation system is included in the analysis, the effect of any significant system nonlinearities should be accounted for when deriving limit loads from limit gust conditions. (b) Continuous Gust Design Criteria. The dynamic response of the airplane to vertical and lateral continuous turbulence must be taken into account. The continuous gust design criteria of Appendix G of this part must be used to establish the dynamic response unless more rational criteria are shown. [Amdt. 25-86, 61 FR 5221, Feb. 9, 1996] Sec. 25.343 Design fuel and oil loads. (a) The disposable load combinations must include each fuel and oil load in the range from zero fuel and oil to the selected maximum fuel and oil load. A structural reserve fuel condition, not exceeding 45 minutes of fuel under the operating conditions in Sec. 25.1001(e) and (f), as applicable, may be selected. (b) If a structural reserve fuel condition is selected, it must be used as the minimum fuel weight condition for showing compliance with the flight load requirements as prescribed in this subpart. In addition-- (1) The structure must be designed for a condition of zero fuel and oil in the wing at limit loads corresponding to-- (i) A maneuvering load factor of +2.25; and (ii) The gust conditions of Sec. 25.341(a) but assuming 85% of the design velocities prescribed in Sec. 25.341(a)(4). (2) Fatigue evaluation of the structure must account for any increase in operating stresses resulting from the design condition of paragraph (b)(1) of this section; and (3) The flutter, deformation, and vibration requirements must also be met with zero fuel. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-18, 33 FR 12226, Aug. 30, 1968; Amdt. 25-72, 55 FR 29775, July 20, 1990; 55 FR 37607, Sept. 12, 1990; Amdt. 25-86, 61 FR 5221, Feb. 9, 1996] Sec. 25.345 High lift devices. (a) If wing flaps are to be used during takeoff, approach, or landing, at the design flap speeds established for these stages of flight under Sec. 25.335(e) and with the wing flaps in the corresponding positions, the airplane is assumed to be subjected to symmetrical maneuvers and gusts. The resulting limit loads must correspond to the conditions determined as follows: (1) Maneuvering to a positive limit load factor of 2.0; and (2) Positive and negative gusts of 25 ft/sec EAS acting normal to the flight path in level flight. Gust loads resulting on each part of the structure must be determined by rational analysis. The analysis must take into account the unsteady aerodynamic characteristics and rigid body motions of the aircraft. The shape of the gust must be as described in Sec. 25.341(a)(2) except that-- [ ...Illustration appears here... ] (b) The airplane must be designed for the conditions prescribed in paragraph (a) of this section, except that the airplane load factor need not exceed 1.0, taking into account, as separate conditions, the effects of- (1) Propeller slipstream corresponding to maximum continuous power at the design flap speeds VF, and with takeoff power at not less than 1.4 times the stalling speed for the particular flap position and associated maximum weight; and (2) A head-on gust of 25 feet per second velocity (EAS). (c) If flaps or other high lift devices are to be used in en route conditions, and with flaps in the appropriate position at speeds up to the flap design speed chosen for these conditions, the airplane is assumed to be subjected to symmetrical maneuvers and gusts within the range determined by- (1) Maneuvering to a positive limit load factor as prescribed in Sec. 25.337(b); and (2) The discrete vertical gust criteria in Sec. 25.341(a). (d) The airplane must be designed for landing at the maximum takeoff weight with a maneuvering load factor of 1.5g and the flaps and similar high lift devices in the landing configuration. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-46, 43 FR 50595, Oct. 30, 1978; Amdt. 25-72, 55 FR 29775, July 20, 1990; 55 FR 37607, Sept. 12, 1990; Amdt. 25-86, 61 FR 5221, Feb. 9, 1996] Sec. 25.349 Rolling conditions. The airplane must be designed for loads resulting from the rolling conditions specified in paragraphs (a) and (b) of this section. Unbalanced aerodynamic moments about the center of gravity must be reacted in a rational or conservative manner, considering the principal masses furnishing the reaching inertia fores. (a) Maneuvering. The following conditions, speeds, and aileron deflections (except as the deflections may be limited by pilot effort) must be considered in combination with an airplane load factor of zero and of two-thirds of the positive maneuvering factor used in design. In determining the required aileron deflections, the torsional flexibility of the wing must be considered in accordance with Sec. 25.301(b): (1) Conditions corresponding to steady rolling velocities must be investigated. In addition, conditions corresponding to maximum angular acceleration must be investigated for airplanes with engines or other weight concentrations outboard of the fuselage. For the angular acceleration conditions, zero rolling velocity may be assumed in the absence of a rational time history investigation of the maneuver. (2) At VA, a sudden deflection of the aileron to the stop is assumed. (3) At VC, the aileron deflection must be that required to produce a rate of roll not less than that obtained in paragraph (a)(2) of this section. (4) At VD, the aileron deflection must be that required to produce a rate of roll not less than one-third of that in paragraph (a)(2) of this section. (b) Unsymmetrical gusts. The airplane is assumed to be subjected to unsymmetrical vertical gusts in level flight. The resulting limit loads must be determined from either the wing maximum airload derived directly from Sec. 25.341(a), or the wing maximum airload derived indirectly from the vertical load factor calculated from Sec. 25.341(a). It must be assumed that 100 percent of the wing air load acts on one side of the airplane and 80 percent of the wing air load acts on the other side. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-86, 61 FR 5222, Feb. 9, 1996] Sec. 25.351 Yawing conditions. The airplane must be designed for loads resulting from the conditions specified in paragraph (a) of this section. Unbalanced aerodynamic moments about the center of gravity must be reacted in a rational or conservative manner considering the principal masses furnishing the reacting inertia forces: (a) Maneuvering. At speeds from VMC to VD, the following maneuvers must be considered. In computing the tail loads, the yawing velocity may be assumed to be zero: (1) With the airplane in unaccelerated flight at zero yaw, it is assumed that the rudder control is suddenly displaced to the maximum deflection, as limited by the control surface stops, or by a 300-pound rudder pedal force, whichever is less. (2) With the rudder deflected as specified in paragraph (a)(1) of this section, it is assumed that the airplane yaws to the resulting sideslip angle. (3) With the airplane yawed to the static sideslip angle corresponding to the rudder deflection specified in paragraph (a)(1) of this section, it is assumed that the rudder is returned to neutral. (b) [Reserved] [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as
amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt.
25-46, 43 FR 50595, Oct. 30, 1978; Amdt. 25-72, 55 FR 29775,
July 20, 1990; 55 FR 37608, Sept. 12, 1990; 55 FR 41415,
Oct. 11, 1990; Amdt. 25-86, 61 FR 5222, Feb. 9,
1996] |
|
|
(a) Each engine mount and its supporting structure must be designed for the effects of-- (1) A limit engine torque corresponding to takeoff power and propeller speed acting simultaneously with 75 percent of the limit loads from flight condition A of Sec. 25.333(b); (2) A limit torque corresponding to the maximum continuous power and propeller speed, acting simultaneously with the limit loads from flight condition A of Sec. 25.333(b); and (3) For turbopropeller installations, in addition to the conditions specified in paragraphs (a)(1) and (2) of this section, a limit engine torque corresponding to takeoff power and propeller speed, multiplied by a factor accounting for propeller control system malfunction, including quick feathering, acting simultaneously with 1g level flight loads. In the absence of a rational analysis, a factor of 1.6 must be used. (b) For turbine engine installations, the engine mounts and supporting structure must be designed to withstand each of the following: (1) A limit engine torque load imposed by sudden engine stoppage due to malfunction or structural failure (such as compressor jamming). (2) A limit engine torque load imposed by the maximum acceleration of the engine. (c) The limit engine torque to be considered under paragraph (a) of this section must be obtained by multiplying mean torque for the specified power and speed by a factor of-- (1) 1.25 for turbopropeller installations; (2) 1.33 for reciprocating engines with five or more cylinders; or (3) Two, three, or four, for engines with four, three, or two cylinders, respectively. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-46, 43 FR 50595, Oct. 30, 1978; Amdt. 25-72, 55 FR 29776, July 20, 1990] Sec. 25.363 Side load on engine mount. (a) Each engine mount and its supporting structure must be designed for a limit load factor in a lateral direction, for the side load on the engine mount, at least equal to the maximum load factor obtained in the yawing conditions but not less than-- (1) 1.33; or (2) One-third of the limit load factor for flight condition A as prescribed in Sec. 25.333(b). (b) The side load prescribed in paragraph (a) of this section may be assumed to be independent of other flight conditions. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970] Sec. 25.365 Pressurized cabin loads. For airplanes with one or more pressurized compartments the following apply: (a) The airplane structure must be strong enough to withstand the flight loads combined with pressure differential loads from zero up to the maximum relief valve setting. (b) The external pressure distribution in flight, and stress concentrations and fatigue effects must be accounted for. (c) If landings may be made with the compartment pressurized, landing loads must be combined with pressure differential loads from zero up to the maximum allowed during landing. (d) The airplane structure must be designed to be able to withstand the pressure differential loads corresponding to the maximum relief valve setting multiplied by a factor of 1.33 for airplanes to be approved for operation to 45,000 feet or by a factor of 1.67 for airplanes to be approved for operation above 45,000 feet, omitting other loads. (e) Any structure, component or part, inside or outside a pressurized compartment, the failure of which could interfere with continued safe flight and landing, must be designed to withstand the effects of a sudden release of pressure through an opening in any compartment at any operating altitude resulting from each of the following conditions: (1) The penetration of the compartment by a portion of an engine following an engine disintegration; (2) Any opening in any pressurized compartment up to the size Ho in square feet; however, small compartments may be combined with an adjacent pressurized compartment and both considered as a single compartment for openings that cannot reasonably be expected to be confined to the small compartment. The size Ho must be computed by the following formula: [ ...equation appears here... ] (3) The maximum opening caused by airplane or equipment failures not shown to be extremely improbable. (f) In complying with paragraph (e) of this section, the fail-safe features of the design may be considered in determining the probability of failure or penetration and probable size of openings, provided that possible improper operation of closure devices and inadvertent door openings are also considered. Furthermore, the resulting differential pressure loads must be combined in a rational and conservative manner with 1-g level flight loads and any loads arising from emergency depressurization conditions. These loads may be considered as ultimate conditions; however, any deformations associated with these conditions must not interfere with continued safe flight and landing. The pressure relief provided by intercompartment venting may also be considered. (g) Bulkheads, floors, and partitions in pressurized compartments for occupants must be designed to withstand the conditions specified in paragraph (e) of this section. In addition, reasonable design precautions must be taken to minimize the probability of parts becoming detached and injuring occupants while in their seats. EDITORIAL NOTE: At 55 FR 29776, July 20, 1990, Sec. 25.365 was amended by removing the words "for occupants" from the introductory sentence, but could not be executed because of an intervening amendment. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-54, 45 FR 60172, Sept. 11, 1980; Amdt. 25-71, 55 FR 13477, Apr. 10, 1990; Amdt. 25-72, 55 FR 29776, July 20, 1990; Amdt. 25-87, 61 FR 28695, June 5, 1996] Sec. 25.367 Unsymmetrical loads due to engine failure. (a) The airplane must be designed for the unsymmetrical loads resulting from the failure of the critical engine. Turbopropeller airplanes must be designed for the following conditions in combination with a single malfunction of the propeller drag limiting system, considering the probable pilot corrective action on the flight controls: (1) At speeds between VMC and VD, the loads resulting from power failure because of fuel flow interruption are considered to be limit loads. (2) At speeds between VMC and VC, the loads resulting from the disconnection of the engine compressor from the turbine or from loss of the turbine blades are considered to be ultimate loads. (3) The time history of the thrust decay and drag build-up occurring as a result of the prescribed engine failures must be substantiated by test or other data applicable to the particular engine-propeller combination. (4) The timing and magnitude of the probable pilot corrective action must be conservatively estimated, considering the characteristics of the particular engine-propeller-airplane combination. (b) Pilot corrective action may be assumed to be initiated at the time maximum yawing velocity is reached, but not earlier than two seconds after the engine failure. The magnitude of the corrective action may be based on the control forces specified in Sec. 25.397(b) except that lower forces may be assumed where it is shown by anaylsis or test that these forces can control the yaw and roll resulting from the prescribed engine failure conditions. Sec. 25.371 Gyroscopic loads. The structure supporting the engines and the auxiliary power units must be designed for the gyroscopic loads associated with the conditions specified in Secs. 25.331, 25.341(a), 25.349 and 25.351 with the engine or auxiliary power units at maximum continuous rpm. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-86, 61 FR 5222, Feb. 9, 1996] Sec. 25.373 Speed control devices. If speed control devices (such as spoilers and drag flaps) are installed for use in en route conditions-- (a) The airplane must be designed for the symmetrical maneuvers prescribed in Sec. 25.333 and Sec. 25.337, the yawing maneuvers prescribed in Sec. 25.351, and the vertical and later gust conditions prescribed in Sec. 25.341(a), at each setting and the maximum speed associated with that setting; and (b) If the device has automatic operating or load limiting features, the airplane must be designed for the maneuver and gust conditions prescribed in paragraph (a) of this section, at the speeds and corresponding device positions that the mechanism allows. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as
amended by Amdt. 25-72, 55 FR 29776, July 20, 1990; Amdt.
25-86, 61 FR 5222, Feb. 9, 1996] |
|
|
The control surfaces must be designed for the limit loads resulting from the flight conditions in Secs. 25.331, 25.341(a), 25.349 and 25.351 and the ground gust conditions in Sec. 25.415, considering the requirements for- (a) Loads parallel to hinge line, in Sec. 25.393; (b) Pilot effort effects, in Sec. 25.397; (c) Trim tab effects, in Sec. 25.407; (d) Unsymmetrical loads, in Sec. 25.427; and (e) Auxiliary aerodynamic surfaces, in Sec. 25.445. [Docket No. 5066, 29 FR 18291, Dec. 24, 1964, as amended at Amdt. 25-86, 61 FR 5222, Feb. 9, 1996] Sec. 25.393 Loads parallel to hinge line. (a) Control surfaces and supporting hinge brackets must be designed for inertia loads acting parallel to the hinge line. (b) In the absence of more rational data, the inertia loads may be assumed to be equal to KW, where-- (1) K=24 for vertical surfaces; (2) K=12 for horizontal surfaces; and (3) W=weight of the movable surfaces. Sec. 25.395 Control system. (a) Longitudinal, lateral, directional, and drag control system and their supporting structures must be designed for loads corresponding to 125 percent of the computed hinge moments of the movable control surface in the conditions prescribed in Sec. 25.391. (b) The system limit loads, except the loads resulting from ground gusts, need not exceed the loads that can be produced by the pilot (or pilots) and by automatic or power devices operating the controls. (c) The loads must not be less than those resulting from application of the minimum forces prescribed in Sec. 25.397(c). [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5672, Apr. 8, 1970; Amdt. 25-72, 55 FR 29776, July 20, 1990] Sec. 25.397 Control system loads. (a) General. The maximum and minimum pilot forces, specified in paragraph (c) of this section, are assumed to act at the appropriate control grips or pads (in a manner simulating flight conditions) and to be reacted at the attachment of the control system to the control surface horn. (b) Pilot effort effects. In the control surface flight loading condition, the air loads on movable surfaces and the corresponding deflections need not exceed those that would result in flight from the application of any pilot force within the ranges specified in paragraph (c) of this section. Two thirds of the maximum values specified for the aileron and elevator may be used if control surface hinge moments are based on reliable data. In applying this criterion, the effects of servo mechanisms, tabs, and automatic pilot systems, must be considered. (c) Limit pilot forces and torques. The limit pilot forces and torques are as follows: [ ...equation/table appears here... ] Minimum / Maximum forces forces or / Control or torquestorques Aileron: Stick: 100 lbs, 40 lbs. /1/ The critical parts of the aileron control system must
be designed for a single tangential force with a limit value
equal to 1.25 times the couple force determined from these
criteria. [Doc. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-38, 41 FR 55466, Dec. 20, 1976; Amdt. 25-72, 55 FR 29776, July 20, 1990] Sec. 25.399 Dual control system. (a) Each dual control system must be designed for the pilots operating in opposition, using individual pilot forces not less than-- (1) 0.75 times those obtained under Sec. 25.395; or (2) The minimum forces specified in Sec. 25.397(c). (b) The control system must be designed for pilot forces applied in the same direction, using individual pilot forces not less than 0.75 times those obtained under Sec. 25.395. Sec. 25.405 Secondary control system. Secondary controls, such as wheel brake, spoiler, and tab controls, must be designed for the maximum forces that a pilot is likely to apply to those controls. The following values may be used: Pilot Control Force Limits (Secondary Controls) [ ...equation appears here... ] not less than 50 lbs. nor more than 150 lbs. (R=radius). (Applicable to any angle within 20 deg. of plane of control). Twist 133 in.-lbs. Push-pull To be chosen by applicant. *Limited to flap, tab, stabilizer, spoiler, and landing gear operation controls. Sec. 25.407 Trim tab effects. The effects of trim tabs on the control surface design conditions must be accounted for only where the surface loads are limited by maximum pilot effort. In these cases, the tabs are considered to be deflected in the direction that would assist the pilot, and the deflections are-- (a) For elevator trim tabs, those required to trim the airplane at any point within the positive portion of the pertinent flight envelope in Sec. 25.333(b), except as limited by the stops; and (b) For aileron and rudder trim tabs, those required to trim the airplane in the critical unsymmetrical power and loading conditions, with appropriate allowance for rigging tolerances. Sec. 25.409 Tabs. (a) Trim tabs. Trim tabs must be designed to withstand loads arising from all likely combinations of tab setting, primary control position, and airplane speed (obtainable without exceeding the flight load conditions prescribed for the airplane as a whole), when the effect of the tab is opposed by pilot effort forces up to those specified in Sec. 25.397(b). (b) Balancing tabs. Balancing tabs must be designed for deflections consistent with the primary control surface loading conditions. (c) Servo tabs. Servo tabs must be designed for deflections consistent with the primary control surface loading conditions obtainable within the pilot maneuvering effort, considering possible opposition from the trim tabs. Sec. 25.415 Ground gust conditions. (a) The control system must be designed as follows for control surface loads due to ground gusts and taxiing downwind: (1) The control system between the stops nearest the surfaces and the cockpit controls must be designed for loads corresponding to the limit hinge moments H of paragraph (a)(2) of this section. These loads need not exceed- (i) The loads corresponding to the maximum pilot loads in Sec. 25.397(c) for each pilot alone; or (ii) 0.75 times these maximum loads for each pilot when the pilot forces are applied in the same direction. (2) The control system stops nearest the surfaces, the control system locks, and the parts of the systems (if any) between these stops and locks and the control surface horns, must be designed for limit hinge moments H obtained from the formula, H=KcSsq, where-- H=limit hinge moment (ft. lbs.); (b) The limit hinge moment factor K for ground gusts must be derived as follows: [ ...equation appears here... ] (a) Aileron 0.75 Control column locked or lashed in
mid-position. /1/ A positive value of K indicates a moment tending to depress the surface, while a negative value of K indicates a moment tending to raise the surface. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-72, 55 FR 29776, July 20, 1990] Sec. 25.427 Unsymmetrical loads. (a) In designing the airplane for lateral gust, yaw maneuver and roll maneuver conditions, account must be taken of unsymmetrical loads on the empennage arising from effects such as slipstream and aerodynamic interference with the wing, vertical fin and other aerodynamic surfaces. (b) The horizontal tail must be assumed to be subjected to unsymmetrical loading conditions determined as follows: (1) 100 percent of the maximum loading from the symmetrical maneuver conditions of Sec. 25.331 and the vertical gust conditions of Sec. 25.341(a) acting separately on the surface on one side of the plane of symmetry; and (2) 80 percent of these loadings acting on the other side. (c) For empennage arrangements where the horizontal tail surfaces have dihedral angles greater than plus or minus 10 degrees, or are supported by the vertical tail surfaces, the surfaces and the supporting structure must be designed for gust velocities specified in Sec. 25.341(a) acting in any orientation at right angles to the flight path. (d) Unsymmetrical loading on the empennage arising from buffet conditions of Sec. 25.305(e) must be taken into account. [Amdt. 25-86, 61 FR 5222, Feb. 9, 1996] Sec. 25.445 Outboard fins. (a) When significant, the aerodynamic influence between auxiliary aerodynamic surfaces, such as outboard fins and winglets, and their supporting aerodynamic surfaces, must be taken into account for all loading conditions including pitch, roll, and yaw maneuvers, and gusts as specified in Sec. 25.341(a) acting at any orientation at right angles to the flight path. (b) To provide for unsymmetrical loading when outboard fins extend above and below the horizontal surface, the critical vertical surface loading (load per unit area) determined under Sec. 25.391 must also be applied as follows: (1) 100 percent to the area of the vertical surfaces above (or below) the horizontal surface. (2) 80 percent to the area below (or above) the horizontal surface. [Docket No. 5066, 29 FR 18291, Dec. 24, 1964, as amended at Amdt. 25-86, 61 FR 5222, Feb. 9, 1996] Sec. 25.457 Wing flaps. Wing flaps, their operating mechanisms, and their supporting structures must be designed for critical loads occurring in the conditions prescribed in Sec. 25.345, accounting for the loads occurring during transition from one flap position and airspeed to another. Sec. 25.459 Special devices. The loading for special devices using aerodynamic surfaces (such as slots, slats, and spoilers) must be determined from test data. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as
amended by Amdt. 25-72, 55 FR 29776, July 20, 1990] |
|
|
(a) Loads and equilibrium. For limit ground loads-- (1) Limit ground loads obtained under this subpart are considered to beexternal forces applied to the airplane structure; and (2) In each specified ground load condition, the external loads must be placed in equilibrium with the linear and angular inertia loads in a rational or conservative manner. (b) Critical centers of gravity. The critical centers of gravity within the range for which certification is requested must be selected so that the maximum design loads are obtained in each landing gear element. Fore and aft, vertical, and lateral airplane centers of gravity must be considered. Lateral displacements of the c.g. from the airplane centerline which would result in main gear loads not greater than 103 percent of the critical design load for symmetrical loading conditions may be selected without considering the effects of these lateral c.g. displacements on the loading of the main gear elements, or on the airplane structure provided-- (1) The lateral displacement of the c.g. results from random passenger or cargo disposition within the fuselage or from random unsymmetrical fuel loading or fuel usage; and (2) Appropriate loading instructions for random disposable loads are included under the provisions of Sec. 25.1583(c)(1) to ensure that the lateral displacement of the center of gravity is maintained within these limits. (c) Landing gear dimension data. Figure 1 of Appendix A contains the basic landing gear dimension data. [Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.473 Ground load conditions and assumptions. (a) For the landing conditions specified in Secs. 25.479 through 25.485, the following apply: (1) The selected limit vertical inertia load factors at the center of gravity of the airplane may not be less than the values that would be obtained-- (i) In the attitude and subject to the drag loads associated with the particular landing condition; (ii) With a limit descent velocity of 10 f.p.s. at the design landing weight (the maximum weight for landing conditions at the maximum descent velocity); and (iii) With a limit descent velocity of 6 f.p.s. at the design takeoff weight (the maximum weight for landing conditions at a reduced descent velocity). (2) Airplane lift, not exceeding the airplane weight, may be assumed to exist throughout the landing impact and to act through the center of gravity of the airplane. (b) The prescribed descent velocities may be modified if it is shown that the airplane has design features that make it impossible to develop these velocities. (c) The minimum limit inertia load factors corresponding to the required limit descent velocities must be determined in accordance with Sec. 25.723(a). [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.477 Landing gear arrangement. Sections 25.479 through 25.485 apply to airplanes with conventional arrangements of main and nose gears, or main and tail gears, when normal operating techniques are used. Sec. 25.479 Level landing conditions. (a) In the level attitude, the airplane is assumed to contact the ground at forward velocity components, ranging from VL1 to 1.25 VL2 parallel to the ground, and to be subjected to the load factors prescribed in Sec. 25.473(a)(1) with-- (1) VL1 equal to VS0 (TAS) at the appropriate landing weight and in standard sea level conditions; and (2) VL2 equal to VS0 (TAS) at the appropriate landing weight and altitudes in a hot day temperature of 41 degrees F. above standard. (b) The effects of increased contact speeds must be investigated if approval of downwind landings exceeding 10 knots is desired. (c) Assuming that the following combinations of vertical and drag components act at the axle centerline, the following apply: (1) For the condition of maximum wheel spin-up load, drag components simulating the forces required to accelerate the wheel rolling assembly up to the specified ground speed must be combined with the vertical ground reactions existing at the instant of peak drag loads. The coefficient of friction between the tires and the ground may be established by considering the effects of skidding velocity and tire pressure. However, this coefficient of friction need not be more than 0.8. This condition must be applied to the landing gear, directly affected attaching structure, and large mass items such as external fuel tanks and nacelles. (2) For the condition of maximum wheel vertical load, an aft acting drag component of not less than 25 percent of the maximum vertical ground reaction must be combined with the maximum ground reaction of Sec. 25.473. (3) For the condition of maximum springback load, forward-acting horizontal loads resulting from a rapid reduction of the spin-up drag loads must be combined with the vertical ground reactions at the instant of the peak forward load. This condition must be applied to the landing gear, directly affected attaching structure, and large mass items such as external fuel tanks and nacelles. (d) For the level landing attitude for airplanes with tail wheels, the conditions specified in paragraphs (a) through (c) of this section must be investigated with the airplane horizontal reference line horizontal in accordance with figure 2 of Appendix A. (e) For the level landing attitude for airplanes with nose wheels, shown in figure 2 of Appendix A, the conditions specified in paragraphs (a) through (c) of this section must be investigated, assuming the following attitudes: (1) An attitude in which the main wheels are assumed to contact the ground with the nose wheel just clear of the ground. (2) If reasonably attainable at the specified descent and forward velocities, an attitude in which the nose and main wheels are assumed to contact the ground simultaneously. For this attitude-- (i) The nose and main gear may be separately investigated under the conditions in paragraph (c) (1) and (3) of this section; and (ii) The pitching moment is assumed, under the condition in paragraph (c)(2) of this section, to be resisted by the nose gear [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.481 Tail-down landing conditions. (a) In the tail-down attitude, the airplane is assumed to contact the ground at forward velocity components, ranging from VL1 to VL2, parallel to the ground, and is subjected to the load factors prescribed in Sec. 25.473(a)(1) with-- (1) VL1 equal to VS0 (TAS) at the appropriate landing weight and in standard sea level conditions; and (2) VL2 equal to VS0 (TAS) at the appropriate landing weight and altitudes in a hot day temperature of 41 degrees F. above standard. The combination of vertical and drag components specified in Sec. 25.479(c) (1) and (3) is considered to be acting at the main wheel axle centerline. (b) For the tail-down landing condition for airplanes with tail wheels, the main and tail wheels are assumed to contact the ground simultaneously, in accordance with figure 3 of Appendix A. Ground reaction conditions on the tail wheel are assumed to act-- (1) Vertically; and (2) Up and aft through the axle at 45 degrees to the ground line. (c) For the tail-down landing condition for airplanes with nose wheels, the airplane is assumed to be at an attitude corresponding to either the stalling angle or the maximum angle allowing clearance with the ground by each part of the airplane other than the main wheels, in accordance with figure 3 of Appendix A, whichever is less. Sec. 25.483 One-wheel landing conditions. For the one-wheel landing condition, the airplane is assumed to be in the level attitude and to contact the ground on one side of the main landing gear, in accordance with Figure 4 of Appendix A. In this attitude-- (a) The ground reactions must be the same as those obtained on that side under Sec. 25.479(c)(2); and (b) Each unbalanced external load must be reacted by airplane inertia in a rational or conservative manner. Sec. 25.485 Side load conditions. (a) For the side load condition, the airplane is assumed to be in the level attitude with only the main wheels contacting the ground, in accordance with figure 5 of Appendix A. (b) Side loads of 0.8 of the vertical reaction (on one side) acting inward and 0.6 of the vertical reaction (on the other side) acting outward must be combined with one-half of the maximum vertical ground reactions obtained in the level landing conditions. These loads are assumed to be applied at the ground contact point and to be resisted by the inertia of the airplane. The drag loads may be assumed to be zero. Sec. 25.487 Rebound landing condition. (a) The landing gear and its supporting structure must be investigated for the loads occurring during rebound of the airplane from the landing surface. (b) With the landing gear fully extended and not in contact with the ground, a load factor of 20.0 must act on the unsprung weights of the landing gear. This load factor must act in the direction of motion of the unsprung weights as they reach their limiting positions in extending with relation to the sprung parts of the landing gear. Sec. 25.489 Ground handling conditions. Unless otherwise prescribed, the landing gear and airplane structure must be investigated for the conditions in Secs. 25.491 through 25.509 with the airplane at the design ramp weight (the maximum weight for ground handling conditions). No wing lift may be considered. The shock absorbers and tires may be assumed to be in their static position. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.491 Takeoff run. The landing gear and the airplane structure are assumed to be subjected to loads not less than those obtained under conditions described in Sec. 25.235. Sec. 25.493 Braked roll conditions. (a) An airplane with a tail wheel is assumed to be in the level attitude with the load on the main wheels, in accordance with figure 6 of Appendix A. The limit vertical load factor is 1.2 at the design landing weight and 1.0 at the design ramp weight. A drag reaction equal to the vertical reaction multiplied by a coefficient of friction of 0.8, must be combined with the vertical ground reaction and applied at the ground contact point. (b) For an airplane with a nose wheel the limit vertical load factor is 1.2 at the design landing weight, and 1.0 at the design ramp weight. A drag reaction equal to the vertical reaction, multiplied by a coefficient of friction of 0.8, must be combined with the vertical reaction and applied at the ground contact point of each wheel with brakes. The following two attitudes, in accordance with figure 6 of Appendix A, must be considered: (1) The level attitude with the wheels contacting the ground and the loads distributed between the main and nose gear. Zero pitching acceleration is assumed. (2) The level attitude with only the main gear contacting the ground and with the pitching moment resisted by angular acceleration. (c) A drag reaction lower than that prescribed in paragraphs (a) and (b) of this section may be used if it is substantiated that an effective drag force of 0.8 times the vertical reaction cannot be attained under any likely loading condition. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.495 Turning. In the static position, in accordance with figure 7 of Appendix A, the airplane is assumed to execute a steady turn by nose gear steering, or by application of sufficient differential power, so that the limit load factors applied at the center of gravity are 1.0 vertically and 0.5 laterally. The side ground reaction of each wheel must be 0.5 of the vertical reaction. Sec. 25.497 Tail-wheel yawing. (a) A vertical ground reaction equal to the static load on the tail wheel, in combination with a side component of equal magnitude, is assumed. (b) If there is a swivel, the tail wheel is assumed to be swiveled 90 deg. to the airplane longitudinal axis with the resultant load passing through the axle. (c) If there is a lock, steering device, or shimmy damper the tail wheel is also assumed to be in the trailing position with the side load acting at the ground contact point. Sec. 25.499 Nose-wheel yaw. (a) A vertical load factor of 1.0 at the airplane center of gravity, and a side component at the nose wheel ground contact equal to 0.8 of the vertical ground reaction at that point are assumed. (b) With the airplane assumed to be in static equilibrium with the loads resulting from the use of brakes on one side of the main landing gear, the nose gear, its attaching structure, and the fuselage structure forward of the center of gravity must be designed for the following loads: (1) A vertical load factor at the center of gravity of 1.0. (2) A forward acting load at the airplane center of gravity of 0.8 times the vertical load on one main gear. (3) Side and vertical loads at the ground contact point on the nose gear that are required for static equilibrium. (4) A side load factor at the airplane center of gravity of zero. (c) If the loads prescribed in paragraph (b) of this section result in a nose gear side load higher than 0.8 times the vertical nose gear load, the design nose gear side load may be limited to 0.8 times the vertical load, with unbalanced yawing moments assumed to be resisted by airplane inertia forces. (d) For other than the nose gear, its attaching structure, and the forward fuselage structure, the loading conditions are those prescribed in paragraph (b) of this section, except that-- (1) A lower drag reaction may be used if an effective drag force of 0.8 times the vertical reaction cannot be reached under any likely loading condition; and (2) The forward acting load at the center of gravity need not exceed the maximum drag reaction on one main gear, determined in accordance with Sec. 25.493(b). (e) With the airplane at design ramp weight, and the nose gear in any steerable position, the combined application of full normal steering torque and a vertical force equal to the maximum static reaction on the nose gear must be considered in designing the nose gear, its attaching structure, and the forward fuselage structure. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970; Amdt. 25-46, 43 FR 50595, Oct. 30, 1978] Sec. 25.503 Pivoting. (a) The airplane is assumed to pivot about one side of the main gear with the brakes on that side locked. The limit vertical load factor must be 1.0 and the coefficient of friction 0.8. (b) The airplane is assumed to be in static equilibrium, with the loads being applied at the ground contact points, in accordance with figure 8 of Appendix A. Sec. 25.507 Reversed braking. (a) The airplane must be in a three point static ground attitude. Horizontal reactions parallel to the ground and directed forward must be applied at the ground contact point of each wheel with brakes. The limit loads must be equal to 0.55 times the vertical load at each wheel or to the load developed by 1.2 times the nominal maximum static brake torque, whichever is less. (b) For airplanes with nose wheels, the pitching moment must be balanced by rotational inertia. (c) For airplanes with tail wheels, the resultant of the ground reactions must pass through the center of gravity of the airplane. Sec. 25.509 Towing loads. (a) The towing loads specified in paragraph (d) of this section must be considered separately. These loads must be applied at the towing fittings and must act parallel to the ground. In addition-- (1) A vertical load factor equal to 1.0 must be considered acting at the center of gravity; (2) The shock struts and tires must be in their static positions; and (3) With WT as the design ramp weight, the towing load, FTOW, is-- (i) 0.3 WT for WT less than 30,000 pounds; (ii) (6WT+450,000)/7 for WT between 30,000 and 100,000 pounds; and (iii) 0.15 WT for WT over 100,000 pounds. (b) For towing points not on the landing gear but near the plane of symmetry of the airplane, the drag and side tow load components specified for the auxiliary gear apply. For towing points located outboard of the main gear, the drag and side tow load components specified for the main gear apply. Where the specified angle of swivel cannot be reached, the maximum obtainable angle must be used. (c) The towing loads specified in paragraph (d) of this section must be reacted as follows: (1) The side component of the towing load at the main gear must be reacted by a side force at the static ground line of the wheel to which the load is applied. (2) The towing loads at the auxiliary gear and the drag components of the towing loads at the main gear must be reacted as follows: (i) A reaction with a maximum value equal to the vertical reaction must be applied at the axle of the wheel to which the load is applied. Enough airplane inertia to achieve equilibrium must be applied. (ii) The loads must be reacted by airplane inertia. (d) The prescribed towing loads are as follows: [ ...table appears here... ] [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.511 Ground load: unsymmetrical loads on multiple-wheel units. (a) General. Multiple-wheel landing gear units are assumed to be subjected to the limit ground loads prescribed in this subpart under paragraphs (b) through (f) of this section. In addition-- (1) A tandem strut gear arrangement is a multiple-wheel unit; and (2) In determining the total load on a gear unit with respect to the provisions of paragraphs (b) through (f) of this section, the transverse shift in the load centroid, due to unsymmetrical load distribution on the wheels, may be neglected. (b) Distribution of limit loads to wheels; tires inflated. The distribution of the limit loads among the wheels of the landing gear must be established for each landing, taxiing, and ground handling condition, taking into account the effects of the following factors: (1) The number of wheels and their physical arrangements. For truck type landing gear units, the effects of any seesaw motion of the truck during the landing impact must be considered in determining the maximum design loads for the fore and aft wheel pairs. (2) Any differentials in tire diameters resulting from a combination of manufacturing tolerances, tire growth, and tire wear. A maximum tire-diameter differential equal to 2/3 of the most unfavorable combination of diameter variations that is obtained when taking into account manufacturing tolerances, tire growth, and tire wear, may be assumed. (3) Any unequal tire inflation pressure, assuming the maximum variation to be +/-5 percent of the nominal tire inflation pressure. (4) A runway crown of zero and a runway crown having a convex upward shape that may be approximated by a slope of 1 1/2 percent with the horizontal. Runway crown effects must be considered with the nose gear unit on either slope of the crown. (5) The airplane attitude. (6) Any structural deflections. (c) Deflated tires. The effect of deflated tires on the structure must be considered with respect to the loading conditions specified in paragraphs (d) through (f) of this section, taking into account the physical arrangement of the gear components. In addition-- (1) The deflation of any one tire for each multiple wheel landing gear unit, and the deflation of any two critical tires for each landing gear unit using four or more wheels per unit, must be considered; and (2) The ground reactions must be applied to the wheels with inflated tires except that, for multiple-wheel gear units with more than one shock strut, a rational distribution of the ground reactions between the deflated and inflated tires, accounting for the differences in shock strut extensions resulting from a deflated tire, may be used. (d) Landing conditions. For one and for two deflated tires, the applied load to each gear unit is assumed to be 60 percent and 50 percent, respectively, of the limit load applied to each gear for each of the prescribed landing conditions. However, for the drift landing condition of Sec. 25.485, 100 percent of the vertical load must be applied. (e) Taxiing and ground handling conditions. For one and for two deflated tires-- (1) The applied side or drag load factor, or both factors, at the center of gravity must be the most critical value up to 50 percent and 40 percent, respectively, of the limit side or drag load factors, or both factors, corresponding to the most severe condition resulting from consideration of the prescribed taxiing and ground handling conditions; (2) For the braked roll conditions of Sec. 25.493 (a) and (b)(2), the drag loads on each inflated tire may not be less than those at each tire for the symmetrical load distribution with no deflated tires; (3) The vertical load factor at the center of gravity must be 60 percent and 50 percent, respectively, of the factor with no deflated tires, except that it may not be less than 1g; and (4) Pivoting need not be considered. (f) Towing conditions. For one and for two deflated tires, the towing load, FTOW, must be 60 percent and 50 percent, respectively, of the load prescribed. Sec. 25.519 Jacking and tie-down provisions. (a) General. The airplane must be designed to withstand the limit load conditions resulting from the static ground load conditions of paragraph (b) of this section and, if applicable, paragraph (c) of this section at the most critical combinations of airplane weight and center of gravity. The maximum allowable load at each jack pad must be specified. (b) Jacking. The airplane must have provisions for jacking and must withstand the following limit loads when the airplane is supported on jacks- (1) For jacking by the landing gear at the maximum ramp weight of the airplane, the airplane structure must be designed for a vertical load of 1.33 times the vertical static reaction at each jacking point acting singly and in combination with a horizontal load of 0.33 times the vertical static reaction applied in any direction. (2) For jacking by other airplane structure at maximum approved jacking weight: (i) The airplane structure must be designed for a vertical load of 1.33 times the vertical reaction at each jacking point acting singly and in combination with a horizontal load of 0.33 times the vertical static reaction applied in any direction. (ii) The jacking pads and local structure must be designed for a vertical load of 2.0 times the vertical static reaction at each jacking point, acting singly and in combination with a horizontal load of 0.33 times the vertical static reaction applied in any direction. (c) Tie-down. If tie-down points are provided, the main tie-down points and local structure must withstand the limit loads resulting from a 65-knot horizontal wind from any direction. [Amdt. 25-81, 59 FR 22102, Apr. 28, 1994] |
|
|
(a) Seaplanes must be designed for the water loads developed during takeoff and landing, with the seaplane in any attitude likely to occur in normal operation, and at the appropriate forward and sinking velocities under the most severe sea conditions likely to be encountered. (b) Unless a more rational analysis of the water loads is made, or the standards in ANC-3 are used, Secs. 25.523 through 25.537 apply. (c) The requirements of this section and Secs. 25.523 through 25.537 apply also to amphibians. Sec. 25.523 Design weights and center of gravity positions. (a) Design weights. The water load requirements must be met at each operating weight up to the design landing weight except that, for the takeoff condition prescribed in Sec. 25.531, the design water takeoff weight (the maximum weight for water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of gravity within the limits for which certification is requested must be considered to reach maximum design loads for each part of the seaplane structure. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.525 Application of loads. (a) Unless otherwise prescribed, the seaplane as a whole is assumed to be subjected to the loads corresponding to the load factors specified in Sec. 25.527. (b) In applying the loads resulting from the load factors prescribed in Sec. 25.527, the loads may be distributed over the hull or main float bottom (in order to avoid excessive local shear loads and bending moments at the location of water load application) using pressures not less than those prescribed in Sec.25.533(b). (c) For twin float seaplanes, each float must be treated as an equivalent hull on a fictitious seaplane with a weight equal to one-half the weight of the twin float seaplane. (d) Except in the takeoff condition of Sec. 25.531, the aerodynamic lift on the seaplane during the impact is assumed to be 2/3 of the weight of the seaplane. Sec. 25.527 Hull and main float load factors. (a) Water reaction load factors nW must be computed in the following manner: (1) For the step landing case [ ...equation appears here... ] (2) For the bow and stern landing cases [ ...equation appears here... ] (b) The following values are used: (1) nW=water reaction load factor (that is, the water reaction divided byseaplane weight). (2) C1=empirical seaplane operations factor equal to 0.012 (except that this factor may not be less than that necessary to obtain the minimum value of step load factor of 2.33). (3) VS0=seaplane stalling speed in knots with flaps extended in the appropriate landing position and with no slipstream effect. (4) <beta>=angle of dead rise at the longitudinal station at which the load factor is being determined in accordance with figure 1 of Appendix B. (5) W=seaplane design landing weight in pounds. (6) K1=empirical hull station weighing factor, in accordance with figure 2 of Appendix B. (7) rx=ratio of distance, measured parallel to hull reference axis, from the center of gravity of the seaplane to the hull longitudinal station at which the load factor is being computed to the radius of gyration in pitch of the seaplane, the hull reference axis being a straight line, in the plane of symmetry, tangential to the keel at the main step. (c) For a twin float seaplane, because of the effect of flexibility of the attachment of the floats to the seaplane, the factor K1 may be reduced at the bow and stern to 0.8 of the value shown in figure 2 of Appendix B. This reduction applies only to the design of the carrythrough and seaplane structure. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.529 Hull and main float landing conditions. (a) Symmetrical step, bow, and stern landing. For symmetrical step, bow, and stern landings, the limit water reaction load factors are those computed under Sec. 25.527. In addition-- (1) For symmetrical step landings, the resultant water load must be applied at the keel, through the center of gravity, and must be directed perpendicularly to the keel line; (2) For symmetrical bow landings, the resultant water load must be applied at the keel, one-fifth of the longitudinal distance from the bow to the step, and must be directed perpendicularly to the keel line; and (3) For symmetrical stern landings, the resultant water load must be applied at the keel, at a point 85 percent of the longitudinal distance from the step to the stern post, and must be directed perpendicularly to the keel line. (b) Unsymmetrical landing for hull and single float seaplanes. Unsymmetrical step, bow, and stern landing conditions must be investigated. In addition-- (1) The loading for each condition consists of an upward component and a side component equal, respectively, to 0.75 and 0.25 tan <beta> times the resultant load in the corresponding symmetrical landing condition; and (2) The point of application and direction of the upward component of the load is the same as that in the symmetrical condition, and the point of application of the side component is at the same longitudinal station as the upward component but is directed inward perpendicularly to the plane of symmetry at a point midway between the keel and chine lines. (c) Unsymmetrical landing; twin float seaplanes. The unsymmetrical loading consists of an upward load at the step of each float of 0.75 and a side load of 0.25 tan <beta> at one float times the step landing load reached under Sec. 25.527. The side load is directed inboard, perpendicularly to the plane of symmetry midway between the keel and chine lines of the float, at the same longitudinal station as the upward load. Sec. 25.531 Hull and main float takeoff condition. For the wing and its attachment to the hull or main float-- (a) The aerodynamic wing lift is assumed to be zero; and (b) A downward inertia load, corresponding to a load factor computed from the following formula, must be applied: [ ...equation appears here... ] where-- n= inertia load factor; [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.533 Hull and main float bottom pressures. (a) General. The hull and main float structure, including frames and bulkheads, stringers, and bottom plating, must be designed under this section. (b) Local pressures. For the design of the bottom plating and stringers and their attachments to the supporting structure, the following pressure distributions must be applied: (1) For an unflared bottom, the pressure at the chine is 0.75 times the pressure at the keel, and the pressures between the keel and chine vary linearly, in accordance with figure 3 of Appendix B. The pressure at the keel (psi) is computed as follows: [ ...equation appears here... ] Pk=pressure (p.s.i.) at the keel; (2) For a flared bottom, the pressure at the beginning of the flare is the same as that for an unflared bottom, and the pressure between the chine and the beginning of the flare varies linearly, in accordance with figure 3 of Appendix B. The pressure distribution is the same as that prescribed in paragraph (b)(1) of this section for an unflared bottom except that the pressure at the chine is computed as follows: [ ...equation appears here... ] where-- Pch=pressure (p.s.i.) at the chine; The area over which these pressures are applied must simulate pressures occurring during high localized impacts on the hull or float, but need not extend over an area that would induce critical stresses in the frames or in the overall structure. (c) Distributed pressures. For the design of the frames, keel, and chine structure, the following pressure distributions apply: (1) Symmetrical pressures are computed as follows: [ ...equation appears here... ] where-- P=pressure (p.s.i.); (2) The unsymmetrical pressure distribution consists of the pressures prescribed in paragraph (c)(1) of this section on one side of the hull or main float centerline and one-half of that pressure on the other side of the hull or main float centerline, in accordance with figure 3 of Appendix B. These pressures are uniform and must be applied simultaneously over the entire hull or main float bottom. The loads obtained must be carried into the sidewall structure of the hull proper, but need not be transmitted in a fore and aft direction as shear and bending loads. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.535 Auxiliary float loads. (a) General. Auxiliary floats and their attachments and supporting structures must be designed for the conditions prescribed in this section. In the cases specified in paragraphs (b) through (e) of this section, the prescribed water loads may be distributed over the float bottom to avoid excessive local loads, using bottom pressures not less than those prescribed in paragraph (g) of this section. (b) Step loading. The resultant water load must be applied in the plane of symmetry of the float at a point three-fourths of the distance from the bow to the step and must be perpendicular to the keel. The resultant limit load is computed as follows, except that the value of L need not exceed three times the weight of the displaced water when the float is completely submerged: [ ...equation appears here... ] where-- L=limit load (lbs.); (c) Bow loading. The resultant limit load must be applied in the plane of symmetry of the float at a point one-fourth of the distance from the bow to the step and must be perpendicular to the tangent to the keel line at that point. The magnitude of the resultant load is that specified in paragraph (b) of this section. (d) Unsymmetrical step loading. The resultant water load consists of a component equal to 0.75 times the load specified in paragraph (a) of this section and a side component equal to 3.25 tan <beta> times the load specified in paragraph (b) of this section. The side load must be applied perpendicularly to the plane of symmetry of the float at a point midway between the keel and the chine. (e) Unsymmetrical bow loading. The resultant water load consists of a component equal to 0.75 times the load specified in paragraph (b) of this section and a side component equal to 0.25 tan <beta> times the load specified in paragraph (c) of this section. The side load must be applied perpendicularly to the plane of symmetry at a point midway between the keel and the chine. (f) Immersed float condition. The resultant load must be applied at the centroid of the cross section of the float at a point one-third of the distance from the bow to the step. The limit load components are as follows: vertical = <rho>gVSO aft = Cx2 <rho>V**2/3 (KVSO)**2. where-- <rho>=mass density of water (slugs/ft.2); (g) Float bottom pressures. The float bottom pressures must be established under Sec. 25.533, except that the value of K2 in the formulae may be taken as1.0. The angle of dead rise to be used in determining the float bottom pressures is set forth in paragraph (b) of this section. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970] Sec. 25.537 Seawing loads. Seawing design loads must be based on applicable test
data. |
|
|
(a) The airplane, although it may be damaged in emergency landing conditions on land or water, must be designed as prescribed in this section to protect each occupant under those conditions. (b) The structure must be designed to give each occupant every reasonable chance of escaping serious injury in a minor crash landing when-- (1) Proper use is made of seats, belts, and all other safety design provisions; (2) The wheels are retracted (where applicable); and (3) The occupant experiences the following ultimate inertia forces acting separately relative to the surrounding structure: (i) Upward, 3.0g (ii) Forward, 9.0g (iii) Sideward, 3.0g on the airframe; and 4.0g on the seats and their attachments. (iv) Downward, 6.0g (v) Rearward, 1.5g (c) The supporting structure must be designed to restrain, under all loads up to those specified in paragraph (b)(3) of this section, each item of mass that could injure an occupant if it came loose in a minor crash landing. (d) Seats and items of mass (and their supporting structure) must not deform under any loads up to those specified in paragraph (b)(3) of this section in any manner that would impede subsequent rapid evacuation of occupants. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5673, Apr. 8, 1970; Amdt. 25-64, 53 FR 17646, May 17, 1988] Sec. 25.562 Emergency landing dynamic conditions. (a) The seat and restraint system in the airplane must be designed as prescribed in this section to protect each occupant during an emergency landing condition when-- (1) Proper use is made of seats, safety belts, and shoulder harnesses provided for in the design; and (2) The occupant is exposed to loads resulting from the conditions prescribed in this section. (b) Each seat type design approved for crew or passenger occupancy during takeoff and landing must successfully complete dynamic tests or be demonstrated by rational analysis based on dynamic tests of a similar type seat, in accordance with each of the following emergency landing conditions. The tests must be conducted with an occupant simulated by a 170-pound anthropomorphic test dummy, as defined by 49 CFR Part 572, Subpart B, or its equivalent, sitting in the normal upright position. (1) A change in downward vertical velocity (Dv) of not less than 35 feet per second, with the airplane's longitudinal axis canted downward 30 degrees with respect to the horizontal plane and with the wings level. Peak floor deceleration must occur in not more than 0.08 seconds after impact and must reach a minimum of 14g. (2) A change in forward longitudinal velocity (Dv) of not less than 44 feet per second, with the airplane's longitudinal axis horizontal and yawed 10 degrees either right or left, whichever would cause the greatest likelihood of the upper torso restraint system (where installed) moving off the occupant's shoulder, and with the wings level. Peak floor deceleration must occur in not more than 0.09 seconds after impact and must reach a minimum of 16g. Where floor rails or floor fittings are used to attach the seating devices to the test fixture, the rails or fittings must be misaligned with respect to the adjacent set of rails or fittings by at least 10 degrees vertically (i.e., out of Parallel) with one rolled 10 degrees. (c) The following performance measures must not be exceeded during the dynamic tests conducted in accordance with paragraph (b) of this section: (1) Where upper torso straps are used for crewmembers, tension loads in individual straps must not exceed 1,750 pounds. If dual straps are used for restraining the upper torso, the total strap tension loads must not exceed 2,000 pounds. (2) The maximum compressive load measured between the pelvis and the lumbar column of the anthropomorphic dummy must not exceed 1,500 pounds. (3) The upper torso restraint straps (where installed) must remain on the occupant's shoulder during the impact. (4) The lap safety belt must remain on the occupant's pelvis during the impact. (5) Each occupant must be protected from serious head injury under the conditions prescribed in paragraph (b) of this section. Where head contact with seats or other structure can occur, protection must be provided so that the head impact does not exceed a Head Injury Criterion (HIC) of 1,000 units. The level of HIC is defined by the equation: [ ...equation appears here... ] Where: t1 is the initial integration time, (6) Where leg injuries may result from contact with seats or other structure, protection must be provided to prevent axially compressive loads exceeding 2,250 pounds in each femur. (7) The seat must remain attached at all points of attachment, although the structure may have yielded. (8) Seats must not yield under the tests specified in paragraphs (b)(1) and (b)(2) of this section to the extent they would impede rapid evacuation of the airplane occupants. [Amdt. 25-64, 53 FR 17646, May 17, 1988] Sec. 25.563 Structural ditching provisions. Structural strength considerations of ditching provisions
must be in accordance with Sec. 25.801(e). |
|
|
(a) General. An evaluation of the strength, detail design, and fabrication must show that catastrophic failure due to fatigue, corrosion, or accidental damage, will be avoided throughout the operational life of the airplane. This evaluation must be conducted in accordance with the provisions of paragraphs (b) and (e) of this section, except as specified in paragraph (c) of this section, for each part of the structure which could contribute to a catastrophic failure (such as wing, empennage, control surfaces and their systems, the fuselage, engine mounting, landing gear, and their related primary attachments). Advisory Circular AC No. 25.571-1 contains guidance information relating to the requirements of this section (copies of the advisory circular may be obtained from the U.S. Department of Transportation, Publications Section M443.1, Washington, D.C. 20590). For turbojet powered airplanes, those parts which could contribute to a catastrophic failure must also be evaluated under paragraph (d) of this section. In addition, the following apply: (1) Each evaluation required by this section must include-- (i) The typical loading spectra, temperatures, and humidities expected in service; (ii) The identification of principal structural elements and detail design points, the failure of which could cause catastrophic failure of the airplane; and (iii) An analysis, supported by test evidence, of the principal structural elements and detail design points identified in paragraph (a)(1)(ii) of this section. (2) The service history of airplanes of similar structural design, taking due account of differences in operating conditions and procedures, may be used in the evaluations required by this section. (3) Based on the evaluations required by this section, inspections or other procedures must be established as necessary to prevent catastrophic failure, and must be included in the Airworthiness Limitations section of the Instruction for Continued Airworthiness required by Sec. 25.1529. (b) Damage-tolerance evaluation. The evaluation must include a determination of the probable locations and modes of damage due to fatigue, corrosion, or accidental damage. The determination must be by analysis supported by test evidence and (if available) service experience. Damage at multiple sites due to prior fatigue exposure must be included where the design is such that this type of damage can be expected to occur. The evaluation must incorporate repeated load and static analyses supported by test evidence. The extent of damage for residual strength evaluation at any time within the operational life must be consistent with the initial detectability and subsequent growth under repeated loads. The residual strength evaluation must show that the remaining structure is able to withstand loads (considered as static ultimate loads) corresponding to the following conditions: (1) The limit symmetrical maneuvering conditions specified in Sec. 25.337 at VC and in Sec. 25.345. (2) The limit gust conditions specified in Sec. 25.341 at the specified speeds up to VC and in Sec. 25.345. (3) The limit rolling conditions specified in Sec. 25.349 and the limit unsymmetrical conditions specified in Secs. 25.367 and 25.427 (a) through (c), at speeds up to VC. (4) The limit yaw maneuvering conditions specified in Sec. 25.351(a) at the specified speeds up to VC. (5) For pressurized cabins, the following conditions: (i) The normal operating differential pressure combined with the expected external aerodynamic pressures applied simultaneously with the flight loading conditions specified in paragraphs (b) (1) through (4) of this section, if they have a significant effect. (ii) The expected external aerodynamic pressures in 1 g flight combined with a cabin differential pressure equal to 1.1 times the normal operating differential pressure without any other load. (6) For landing gear and directly-affected airframe structure, the limit ground loading conditions specified in Secs. 25.473, 25.491, and 25.493. If significant changes in structural stiffness or geometry, or both, follow from a structural failure, or partial failure, the effect on damage tolerance must be further investigated. (c) Fatigue (safe-life) evaluation. Compliance with the damage-tolerance requirements of paragraph (b) of this section is not required if the applicant establishes that their application for particular structure is impractical. This structure must be shown by analysis, supported by test evidence, to be able to withstand the repeated loads of variable magnitude expected during its service life without detectable cracks. Appropriate safe life scatt |
