|
|
We help Organizations quickly Conceptualize, Design, Develop, and Implement Innovative Cost-Effective Solutions for Avionics, Aircraft, and Flight Guidance-Navigation-Control Systems. |
|---|---|
|
|
|
Home
YOU
US
What
We Can
Do
What
We Have
Done -
On
Learjets
Why
ASTECH
ASTECH's
Founder
Expert's
Corner-
FAA FAR Part 23 B
Links
In
Closing
|
Subpart B--Flight 23.21 Proof of compliance. 23.45 General. 23.141 General. Controllability and Maneuverability 23.143 General. 23.161 Trim. 23.171 General. 23.201 Wings level stall. 23.221 Spinning. Ground and Water Handling Characteristics 23.231 Longitudinal stability and control. Miscellaneous Flight Requirements 23.251 Vibration and buffeting. Authority: 49 U.S.C. 106(g), 40113, 44701-44702,
44704. |
|
(a) Each requirement of this subpart must be met at each appropriate combination of weight and center of gravity within the range of loading conditions for which certification is requested. This must be shown-- (1) By tests upon an airplane of the type for which
certification is requested, or by calculations based on, and
equal in accuracy to, the results of testing; and (b) The following general tolerances are allowed during flight testing. However, greater tolerances may be allowed in particular tests: Item Tolerance Weight +5, -10. Critical items affected by weight +5, -1. C.G +/-7 total travel. Sec. 23.23 Load distribution limits. (a) Ranges of weights and centers of gravity within which the airplane may be safely operated must be established. If a weight and center of gravity combination is allowable only within certain lateral load distribution limits that could be inadvertently exceeded, these limits must be established for the corresponding weight and center of gravity combinations. (b) The load distribution limits may not exceed any of the following: (1) The selected limits; [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964, as amended by Amdt. 23-17, 41 FR 55463, Dec. 20, 1976; Amdt. 23-45, 58 FR 42156, Aug. 6, 1993] Sec. 23.25 Weight limits. (a) Maximum weight. The maximum weight is the highest weight at which compliance with each applicable requirement of this part (other than those complied with at the design landing weight) is shown. The maximum weight must be established so that it is-- (1) Not more than the least of-- (i) The highest weight
selected by the applicant; or (ii) The design maximum
weight, which is the highest weight at which compliance with
each applicable structural loading condition of this part
(other than those complied with at the design landing
weight) is shown; or (iii) The highest weight at which
compliance with each applicable flight requirement is shown,
and (b) Minimum weight. The minimum weight (the lowest weight at which compliance with each applicable requirement of this part is shown) must be established so that it is not more than the sum of-- (1) The empty weight determined under Sec. 23.29; [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964, as amended by Amdt. 23-7, 34 FR 13086, Aug. 13, 1969; Amdt. 23-21, 43 FR 2317, Jan. 16, 1978; Amdt. 23-34, 52 FR 1825, Jan. 15, 1987; Amdt. No. 23-45, 58 FR 42156, Aug. 6, 1993; Amdt. 23-50, 61 FR 5183, Feb. 9, 1996] Sec. 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with-- (1) Fixed ballast; (b) The condition of the airplane at the time of determining empty weight must be one that is well defined and can be easily repeated. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964; 30 FR 258, Jan. 9, 1965, as amended by Amdt. 23-21, 43 FR 2317, Jan. 16, 1978] Sec. 23.31 Removable ballast. Removable ballast may be used in showing compliance with the flight requirements of this subpart, if-- (a) The place for carrying ballast is properly designed and installed, and is marked under Sec. 23.1557; and (b) Instructions are included in the airplane flight manual, approved manual material, or markings and placards, for the proper placement of the removable ballast under each loading condition for which removable ballast is necessary. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964; 30 FR 258, Jan. 9, 1965, as amended by Amdt. 23-13, 37 FR 20023, Sept. 23, 1972] Sec. 23.33 Propeller speed and pitch limits. (a) General. The propeller speed and pitch must be limited to values that will assure safe operation under normal operating conditions. (b) Propellers not controllable in flight. For each propeller whose pitch cannot be controlled in flight-- (1) During takeoff and initial climb at the all engine(s) operating climb speed specified in Sec. 23.65, the propeller must limit the engine r.p.m., at full throttle or at maximum allowable takeoff manifold pressure, to a speed not greater than the maximum allowable takeoff r.p.m.; and (2) During a closed throttle glide, at VNE, the propeller may not cause an engine speed above 110 percent of maximum continuous speed. (c) Controllable pitch propellers without constant speed controls. Each propeller that can be controlled in flight, but that does not have constant speed controls, must have a means to limit the pitch range so that-- (1) The lowest possible pitch allows compliance with
paragraph (b)(1) of this section; and (d) Controllable pitch propellers with constant speed controls. Each controllable pitch propeller with constant speed controls must have-- (1) With the governor in operation, a means at the
governor to limit the maximum engine speed to the maximum
allowable takeoff r.p.m.; and $Doc. No. 4080, 29 FR 17955, Dec. 18, 1964; 30 FR 258, Jan. 9, 1965, as amended by Amdt. No. 23-45, 58 FR 42156, Aug. 6, 1993; Amdt. 23-50, 61 FR 5183, Feb. 9, 1996] |
|
|
(a) Unless otherwise prescribed, the performance requirements of this part must be met for-- (1) Still air and standard atmosphere; and (b) Performance data must be determined over not less
than the following ranges of conditions-- (c) Performance data must be determined with the cowl flaps or other means for controlling the engine cooling air supply in the position used in the cooling tests required by Sec. 23.1041 to Sec. 23.1047. (d) The available propulsive thrust must correspond to engine power, not exceeding the approved power, less-- (1) Installation losses; and (e) The performance, as affected by engine power or thrust, must be based on a relative humidity: (1) Of 80 percent at and below standard temperature; and (2) From 80 percent, at the standard temperature, varying linearly down to 34 percent at the standard temperature plus 50 deg.F. (f) Unless otherwise prescribed, in determining the takeoff and landing distances, changes in the airplane's configuration, speed, and power must be made in accordance with procedures established by the applicant for operation in service. These procedures must be able to be executed consistently by pilots of average skill in atmospheric conditions reasonably expected to be encountered in service. (g) The following, as applicable, must be determined on a smooth, dry, hard-surfaced runway-- (1) Takeoff distance of Sec. 23.53(b); Note: The effect on these distances of operation on other types of surfaces (for example, grass, gravel) when dry, may be determined or derived and these surfaces listed in the Airplane Flight Manual in accordance with Sec. 23.1583(p). (h) For commuter category airplanes, the following also apply: (1) Unless otherwise prescribed, the applicant must
select the takeoff, enroute, approach, and landing
configurations for the airplane. [Amdt. 23-50, 61 FR 5184, Feb. 9, 1996] Sec. 23.49 Stalling period. (a) VSO and VS1 are the stalling speeds or the minimum steady flight speeds, in knots (CAS), at which the airplane is controllable with-- (1) For reciprocating engine-powered airplanes, the
engine(s) idling, the throttle(s) closed or at not more than
the power necessary for zero thrust at a speed not more than
110 percent of the stalling speed; (b) VSO and VS1 must be determined by flight tests, using the procedure and meeting the flight characteristics specified in Sec. 23.201. (c) Except as provided in paragraph (d) of this section, VSO and VS1 at maximum weight must not exceed 61 knots for-- (1) Single-engine airplanes; and (d) All single-engine airplanes, and those multiengine airplanes of 6,000 pounds or less maximum weight with a VSO of more than 61 knots that do not meet the requirements of Sec. 23.67(a)(1), must comply with Sec. 23.562(d). [Amdt. 23-50, 61 FR 5184, Feb. 9, 1996] Sec. 23.51 Takeoff speeds. (a) For normal, utility, and acrobatic category airplanes, rotation speed, VR, is the speed at which the pilot makes a control input, with the intention of lifting the airplane out of contact with the runway or water surface. (1) For multiengine landplanes, VR, must not be less than
the greater of 1.05 VMC; or 1.10 VS1; (b) For normal, utility, and acrobatic category
airplanes, the speed at 50 feet above the takeoff surface
level must not be less than: (c) For commuter category airplanes, the following apply: (l) V1 must be established in relation to VEF as follows:
(i) VEF is the calibrated airspeed at which the critical
engine is assumed to fail. VEF must be selected by the
applicant but must not be less than 1.05 VMC determined
under Sec. 23.149(b) or, at the option of the applicant, not
less than VMCG determined under Sec. 23.149(f).(ii) The
takeoff decision speed, V1, is the calibrated airspeed on
the ground at which, as a result of engine failure or other
reasons, the pilot is assumed to have made a decision to
continue or discontinue the takeoff. The takeoff decision
speed, V1, must be selected by the applicant but must not be
less than VEF plus the speed gained with the critical engine
inoperative during the time interval between the instant at
which the critical engine is failed and the instant at which
the pilot recognizes and reacts to the engine failure, as
indicated by the pilot's application of the first retarding
means during the accelerate-stop determination of Sec.
23.55. [Amdt. 23-50, 5184, Feb. 9, 1996] Sec. 23.53 Takeoff performance. (a) For normal, utility, and acrobatic category airplanes, the takeoff distance must be determined in accordance with paragraph (b) of this section, using speeds determined in accordance with Sec. 23.51 (a) and (b). (b) For normal, utility, and acrobatic category airplanes, the distance required to takeoff and climb to a height of 50 feet above the takeoff surface must be determined for each weight, altitude, and temperature within the operational limits established for takeoff with-- (1) Takeoff power on each engine; (2) Wing flaps in the takeoff position(s); and (3) Landing gear extended. (c) For commuter category airplanes, takeoff performance, as required by Secs. 23.55 through 23.59, must be determined with the operating engine(s) within approved operating limitations. [Amdt. 23-50, 61 FR 5185, Feb. 9, 1996] Sec. 23.55 Accelerate-stop distance. For each commuter category airplane, the accelerate-stop distance must be determined as follows: (a) The accelerate-stop distance is the sum of the distances necessary to-- (1) Accelerate the airplane from a standing start to VEF
with all engines operating; (b) Means other than wheel brakes may be used to determine the accelerate- stop distances if that means-- (1) Is safe and reliable; [Amdt. 23-34, 52 FR 1826, Jan. 15, 1987, as amended by Amdt. 23-50, 61 FR 5185, Feb. 9, 1996] Sec. 23.57 Takeoff path. For each commuter category airplane, the takeoff path is as follows: (a) The takeoff path extends from a standing start to a point in the takeoff at which the airplane is 1500 feet above the takeoff surface at or below which height the transition from the takeoff to the enroute configuration must be completed; and (1) The takeoff path must be based on the procedures
prescribed in Sec. 23.45; (b) During the acceleration to speed V2, the nose gear may be raised off the ground at a speed not less than VR. However, landing gear retraction must not be initiated until the airplane is airborne. (c) During the takeoff path determination, in accordance with paragraphs (a) and (b) of this section-- (1) The slope of the airborne part of the takeoff path
must not be negative at any point; (d) The takeoff path to 35 feet above the takeoff surface must be determined by a continuous demonstrated takeoff. (e) The takeoff path to 35 feet above the takeoff surface must be determined by synthesis from segments; and (1) The segments must be clearly defined and must be related to distinct changes in configuration, power, and speed; (2) The weight of the airplane, the configuration, and the power must be assumed constant throughout each segment and must correspond to the most critical condition prevailing in the segment; and (3) The takeoff flight path must be based on the airplane's performance without utilizing ground effect. [Amdt. 23-34, 52 FR 1827, Jan. 15, 1987, as amended by Amdt. 23-50, 61 FR 5185, Feb. 9, 1996] Sec. 23.59 Takeoff distance and takeoff run. For each commuter category airplane, the takeoff distance and, at the option of the applicant, the takeoff run, must be determined. (a) Takeoff distance is the greater of-- (1) The horizontal distance along the takeoff path from
the start of the takeoff to the point at which the airplane
is 35 feet above the takeoff surface as determined under
Sec. 23.57; or (b) If the takeoff distance includes a clearway, the
takeoff run is the greater of-- [Amdt. 23-34, 52 FR 1827, Jan. 15, 1987, as amended by Amdt. 23-50, 61 FR 5185, Feb. 9, 1996] Sec. 23.61 Takeoff flight path. For each commuter category airplane, the takeoff flight path must be determined as follows: (a) The takeoff flight path begins 35 feet above the takeoff surface at the end of the takeoff distance determined in accordance with Sec. 23.59. (b) The net takeoff flight path data must be determined so that they represent the actual takeoff flight paths, as determined in accordance with Sec. 23.57 and with paragraph (a) of this section, reduced at each point by a gradient of climb equal to-- (1) 0.8 percent for two-engine airplanes; (c) The prescribed reduction in climb gradient may be applied as an equivalent reduction in acceleration along that part of the takeoff flight path at which the airplane is accelerated in level flight. [Amdt. 23-34, 52 FR 1827, Jan. 15, 1987] Sec. 23.63 Climb: general. (a) Compliance with the requirements of Secs. 23.65, 23.66, 23.67, 23.69, and 23.77 must be shown-- (1) Out of ground effect; and (b) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of 6,000 pounds or less maximum weight, compliance must be shown with Sec. 23.65(a), Sec. 23.67(a), where appropriate, and Sec. 23.77(a) at maximum takeoff or landing weight, as appropriate, in a standard atmosphere. (c) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes in the normal, utility, and acrobatic category, compliance must be shown at weights as a function of airport altitude and ambient temperature, within the operational limits established for takeoff and landing, respectively, with-- (1) Sections 23.65(b) and 23.67(b) (1) and (2), where
appropriate, for takeoff, and (d) For commuter category airplanes, compliance must be shown at weights as a function of airport altitude and ambient temperature within the operational limits established for takeoff and landing, respectively, with-- (1) Sections 23.67(c)(1), 23.67(c)(2), and 23.67(c)(3)
for takeoff; and [Amdt. 23-50, 61 FR 5186, Feb. 9, 1996] Sec. 23.65 Climb: all engines operating. (a) Each normal, utility, and acrobatic category reciprocating engine- powered airplane of 6,000 pounds or less maximum weight must have a steady climb gradient at sea level of at least 8.3 percent for landplanes or 6.7 percet for seaplanes and amphibians with-- (1) Not more than maximum continuous power on each
engine; (b) Each normal, utility, and acrobatic category reciprocating engine- powered airplane of more than 6,000 pounds maximum weight and turbine engine- powered airplanes in the normal, utility, and acrobatic category must have a steady gradient of climb after takeoff of at least 4 percent with (1) Take off power on each engine; [Amdt. 23-50, 61 FR 5186, Feb. 9, 1996] Sec. 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category reciprocating engine-powered airplanes of more than 6,000 pounds maximum weight, and turbine engine- powered airplanes in the normal, utility, and acrobatic category, the steady gradient of climb or descent must be determined at each weight, altitude, and ambient temperature within the operational limits established by the applicant with-- (a) The critical engine inoperative and its propeller in the position it rapidly and automatically assumes; (b) The remaining engine(s) at takeoff power; (c) The landing gear extended, except that if the landing gear can be retracted in not more than seven seconds, the test may be conducted with the gear retracted; (d) The wing flaps in the takeoff position(s): (e) The wings level; and (f) A climb speed equal to that achieved at 50 feet in the demonstration of Sec. 23.53. [Amdt. 23-50, 61 FR 5186, Feb. 9, 1996] Sec. 23.67 Climb: One engine inoperative. (a) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of 6,000 pounds or less maximum weight, the following apply: (1) Except for those airplanes that meet the requirements prescribed in Sec. 23.562(d), each airplane with a VSO of more than 61 knots must be able to maintain a steady climb gradient of at least 1.5 percent at a pressure altitude of 5,000 feet with the-- (i) Critical engine inoperative and its propeller in the
minimum drag position; (2) For each airplane that meets the requirements prescribed in Sec. 23.562(d), or that has a VSO of 61 knots or less, the steady gradient of climb or descent at a pressure altitude of 5,000 feet must be determined with the-- (i) Critical engine inoperative and its propeller in the
minimum drag position; (b) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes in the normal, utility, and acrobatic category-- (1) The steady gradient of climb at an altitude of 400 feet above the takeoff must be measurably positive with the-- (i) Critical engine inoperative and its propeller in the
minimum drag position; (2) The steady gradient of climb must not be less than 0.75 percent at an altitude of 1,500 feet above the takeoff surface, or landing surface, as appropriate, with the-- (i) Critical engine inoperative and its propeller in the
minimum drag position; (c) For commuter category airplanes, the following apply: (1) Takeoff; landing gear extended. The steady gradient of climb at the altitude of the takeoff surface must be measurably positive for two-engine airplanes, not less than 0.3 percent for three-engine airplanes, or 0.5 percent for four-engine airplanes with-- (i) The critical engine inoperative and its propeller in
the position it rapidly and automatically assumes; (2) Takeoff; landing gear retracted. The steady gradient of climb at an altitude of 400 feet above the takeoff surface must be not less than 2.0 percent of two-engine airplanes, 2.3 percent for three-engine airplanes, and 2.6 percent for four-engine airplanes with-- (i) The critical engine inoperative and its propeller in
the position it rapidly and automatically assumes; (3) Enroute. The steady gradient of climb at an altitude of 1,500 feet above the takeoff or landing surface, as appropriate, must be not less than 1.2 percent for two-engine airplanes, 1.5 percent for three-engine airplanes, and 1.7 percent for four-engine airplanes with-- (i) The critical engine inoperative and its propeller in
the minimum drag position; (4) Discontinued approach. The steady gradient of climb at an altitude of 400 feet above the landing surface must be not less than 2.1 percent for two- engine airplanes, 2.4 percent for three-engine airplanes, and 2.7 percent for four-engine airplanes, with-- (i) The critical engine inoperative and its propeller in
the minimum drag position; [Amdt. 23-50, 61 FR 5186, Feb. 9, 1996] Sec. 23.69 Enroute climb/descent. (a) All engines operating. The steady gradient and rate of climb must be determined at each weight, altitude, and ambient temperature within the operational limits established by the applicant with-- (1) Not more than maximum continuous power on each
engine; (b) One engine inoperative. The steady gradient and rate of climb/descent must be determined at each weight, altitude, and ambient temperature within the operational limits established by the applicant with-- (1) The critical engine inoperative and its propeller in
the minimum drag position; [Amdt. 23-50, 61 FR 5187, Feb. 9, 1996] Sec. 23.71 Glide: Single-engine airplanes. The maximum horizontal distance traveled in still air, in nautical miles, per 1,000 feet of altitude lost in a glide, and the speed necessary to achieve this must be determined with the engine inoperative, its propeller in the minimum drag position, and landing gear and wing flaps in the most favorable available position. [Amdt. 23-50, 61 FR 5187, Feb. 9, 1996] Sec. 23.73 Reference landing approach speed. (a) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of 6,000 pounds or less maximum weight, the reference landing approach speed, VREF, must not be less than the greater of VMC, determined in Sec. 23.149(b) with the wing flaps in the most extended takeoff position, and 1.3 VSO. (b) For normal, utility, and acrobatic category reciprocating engine- powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes in the normal, utility, and acrobatic category, the reference landing approach speed, VREF, must not be less than the greater of VMC, determined in Sec. 23.149(c), and 1.3 VSO. (c) For commuter category airplanes, the reference landing approach speed, VREF, must not be less than the greater of 1.05 VMC, determined in Sec. 23.149(c), and 1.3 VSO. [Amdt. 23-50, 61 FR 5187, Feb. 9, 1996] Sec. 23.75 Landing distance. The horizontal distance necessary to land and come to a complete stop from a point 50 feet above the landing surface must be determined, for standard temperatures at each weight and altitude within the operational limits established for landing, as follows: (a) A steady approach at not less than VREF, determined in accordance with Sec. 23.73 (a), (b), or (c), as appropriate, must be maintained down to the 50 foot height and-- (1) The steady approach must be at a gradient of descent not greater than 5.2 percent (3 degrees) down to the 50-foot height. (2) In addition, an applicant may demonstrate by tests that a maximum steady approach gradient steeper than 5.2 percent, down to the 50-foot height, is safe. The gradient must be established as an operating limitation and the information necessary to display the gradient must be available to the pilot by an appropriate instrument. (b) A constant configuration must be maintained throughout the maneuver. (c) The landing must be made without excessive vertical acceleration or tendency to bounce, nose over, ground loop, porpoise, or water loop. (d) It must be shown that a safe transition to the balked landing conditions of Sec. 23.77 can be made from the conditions that exist at the 50 foot height, at maximum landing weight, or at the maximum landing weight for altitude and temperature of Sec. 23.63 (c)(2) or (d)(2), as appropriate. (e) The brakes must be used so as to not cause excessive wear of brakes or tires. (f) Retardation means other than wheel brakes may be used if that means-- (1) Is safe and reliable; and (2) Is used so that consistent results can be expected in service. (g) If any device is used that depends on the operation of any engine, and the landing distance would be increased when a landing is made with that engine inoperative, the landing distance must be determined with that engine inoperative unless the use of other compensating means will result in a landing distance not more than that with each engine operating. [Amdt. 23-21, 43 FR 2318, Jan. 16, 1978, as amended by Amdt. 23-34, 52 FR 1828, Jan. 15, 1987; Amdt. 23-42, 56 FR 351, Jan. 3, 1991; Amdt. 23-50, 61 FR 5187, Feb. 9, 1996] Sec. 23.77 Balked landing. (a) Each normal, utility, and acrobatic category reciprocating engine- powered airplane at 6,000 pounds or less maximum weight must be able to maintain a steady gradient of climb at sea level of at least 3.3 percent with-- (1) Takeoff power on each engine; (b) Each normal, utility, and acrobatic category reciprocating engine- powered airplane of more than 6,000 pounds maximum weight and each normal, utility, and acrobatic category turbine engine-powered airplane must be able to maintain a steady gradient of climb of at least 2.5 percent with-- (1) Not more than the power that is available on each
engine eight seconds after initiation of movement of the
power controls from minimum flight-idle position; (c) Each commuter category airplane must be able to maintain a steady gradient of climb of at least 3.2 percent with-- (1) Not more than the power that is available on each
engine eight seconds after initiation of movement of the
power controls from the minimum flight idle position; [Amdt. 23-60, 61 FR 5187, Feb. 9, 1996] |
|
|
The airplane must meet the requirements of Secs. 23.143 through 23.253 at all practical loading conditions and operating altitudes for which certification has been requested, not exceeding the maximum operating altitude established under Sec. 23.1527, and without requiring exceptional piloting skill, alertness, or strength. [Amdt. 23-45, 58 FR 42156, Aug. 6, 1993] |
|
|
(a) The airplane must be safely controllable and maneuverable during all flight phases including-- (1) Takeoff; (2) Climb; (3) Level flight; (4) Descent; (5) Go-around; and (6) Landing (power on and power off) with the wing flaps extended and retracted. (b) It must be possible to make a smooth transition from one flight condition to another (including turns and slips) without danger of exceeding the limit load factor, under any probable operating condition (including, for multiengine airplanes, those conditions normally encountered in the sudden failure of any engine). (c) If marginal conditions exist with regard to required pilot strength, the control forces necessary must be determined by quantitative tests. In no case may the control forces under the conditions specified in paragraphs (a) and (b) of this section exceed those prescribed in the following table: Values in pounds force applied to the relevant control Pitch Roll Yaw (a) For temporary application: Stick 60 30 Wheel (Two hands on rim) 75 50 (b) For prolonged application 10 5 20 [Doc. No, 4080, 29 FR 17955, Dec. 18, 1964, as amended by Amdt. 23-14, 38 FR 31819, Nov. 19, 1973; Amdt. 23-17, 41 FR 55464, Dec. 20, 1976; Amdt. 23-45, 58 FR 42157, Aug. 6, 1993; Amdt. 23-50, 61 FR 5188, Feb. 9, 1996] Sec. 23.145 Longitudinal control. (a) With the airplane as nearly as possible in trim at 1.3 VS1, it must be possible, at speeds below the trim speed, to pitch the nose downward so that the rate of increase in airspeed allows prompt acceleration to the trim speed with-- (1) Maximum continuous power on each engine; (2) Power off; and (3) Wing flap and landing gear-- (i) retracted, and (ii) extended. (b) Unless otherwise required, it must be possible to carry out the following maneuvers without requiring the application of single-handed control forces exceeding those specified in Sec. 23.143(c). The trimming controls must not be adjusted during the maneuvers: (1) With the landing gear extended, the flaps retracted, and the airplanes as nearly as possible in trim at 1.4 VS1, extend the flaps as rapidly as possible and allow the airspeed to transition from 1.4 VS1 to 1.4 VSO: (i) With power off; and (ii) With the power necessary to maintain level flight in the initial condition. (2) With landing gear and flaps extended, power off, and the airplane as nearly as possible in trim at 1.3 VSO, quickly apply takeoff power and retract the flaps as rapidly as possible to the recommended go around setting and allow the airspeed to transition from 1.3 VSO to 1.3 VS1. Retract the gear when a positive rate of climb is established. (3) With landing gear and flaps extended, in level flight, power necessary to attain level flight at 1.1 VSO, and the airplane as nearly as possible in trim, it must be possible to maintain approximately level flight while retracting the flaps as rapidly as possible with simultaneous application of not more than maximum continuous power. If gated flat positions are provided, the flap retraction may be demonstrated in stages with power and trim reset for level flight at 1.1 VS1, in the initial configuration for each stage-- (i) From the fully extended position to the most extended gated position; (ii) Between intermediate gated positions, if applicable; and (iii) From the least extended gated position to the fully retracted position. (4) With power off, flaps and landing gear retracted and the airplane as nearly as possible in trim at 1.4 VS1, apply takeoff power rapidly while maintaining the same airspeed. (5) With power off, landing gear and flaps extended, and the airplane as nearly as possible in trim at VREF, obtain and maintain airspeeds between 1.1 VSO, and either 1.7 VSO or VFE, whichever is lower without requiring the application of two-handed control forces exceeding those specified in Sec. 23.143(c). (6) With maximum takeoff power, landing gear retracted, flaps in the takeoff position, and the airplane as nearly as possible in trim at VFE appropriate to the takeoff flap position, retract the flaps as rapidly as possible while maintaining constant speed. (c) At speeds above VMO/MMO, and up to the maximum speed shown under Sec. 23.251, a maneuvering capability of 1.5 g must be demonstrated to provide a margin to recover from upset or inadvertent speed increase. (d) It must be possible, with a pilot control force of not more than 10 pounds, to maintain a speed of not more than VREF during a power-off glide with landing gear and wing flaps extended, for any weight of the airplane, up to and including the maximum weight. (e) By using normal flight and power controls, except as otherwise noted in paragraphs (e)(1) and (e)(2) of this section, it must be possible to establish a zero rate of descent at an attitude suitable for a controlled landing without exceeding the operational and structural limitations of the airplane, as follows: (1) For single-engine and multiengine airplanes, without the use of the primary longitudinal control system. (2) For multiengine airplanes-- (i) Without the use of the primary directional control; and (ii) If a single failure of any one connecting or transmitting link would affect both the longitudinal and directional primary control system, without the primary longitudinal and directional control system. [Amdt. 23-45, 58 FR 42157, Aug. 6, 1993; 58 FR 51970, Oct. 5, 1993; Amdt. 23-50, 61 FR 5188, Feb. 9, 1996] Sec. 23.147 Directional and lateral control. (a) For each multiengine airplane, it must be possible, while holding the wings level within five degrees, to make sudden changes in heading safely in both directions. This ability must be shown at 1.4 VS1 with heading changes up to 15 degrees, except that the heading change at which the rudder force corresponds to the limits specified in Sec. 23.143 need not be exceeded, with the-- (1) Critical engine inoperative and its propeller in the minimum drag position; (2) Remaining engines at maximum continuous power; (3) Landing gear-- (i) Retracted; and (ii) Extended; and (4) Flaps retracted. (b) For each multiengine airplane, it must be possible to regain full control of the airplane without exceeding a bank angle of 45 degrees, reaching a dangerous attitude or encountering dangerous characteristics, in the event of a sudden and complete failure of the critical engine, making allowance for a delay of two seconds in the initiation of recovery action appropriate to the situation, with the airplane initially in trim, in the following condition: (1) Maximum continuous power on each engine; (2) The wing flaps retracted; (3) The landing gear retracted; (4) A speed equal to that at which compliance with Sec. 23.69(a) has been shown; and (5) All propeller controls in the position at which compliance with Sec. 23.69(a) has been shown. (c) For all airplanes, it must be shown that the airplane is safely controllable without the use of the primary lateral control system in any all-engine configuration(s) and at any speed or altitude within the approved operating envelope. It must also be shown that the airplane's flight characteristics are not impaired below a level needed to permit continued safe flight and the ability to maintain attitudes suitable for a controlled landing without exceeding the operational and structural limitations of the airplane. If a single failure of any one connecting or transmitting link in the lateral control system would also cause the loss of additional control system(s), compliance with the above requirement must be shown with those additional systems also assumed to be inoperative. [Amdt. 23-50, 61 FR 5188, Feb. 9, 1996] Sec. 23.149 Minimum control speed. (a) VMC is the calibrated airspeed at which, when the critical engine is suddenly made inoperative, it is possible to maintain control of the airplane with that engine still inoperative, and thereafter maintain straight flight at the same speed with an angle of bank of not more than 5 degrees. The method used to simulate critical engine failure must represent the most critical mode of powerplant failure expected in service with respect to controllability. (b) VMC for takeoff must not exceed 1.2 VS1, where VS1 is determined at the maximum takeoff weight. VMC must be determined with the most unfavorable weight and center of gravity position and with the airplane airborne and the ground effect negligible, for the takeoff configuration(s) with-- (1) Maximum available takeoff power initially on each engine; (2) The airplane trimmed for takeoff; (3) Flaps in the takeoff position(s); (4) Landing gear retracted; and (5) All propeller controls in the recommended takeoff position throughout. (c) For all airplanes except reciprocating engine-powered airplanes of 6,000 pounds or less maximum weight, the conditions of paragraph (a) of this section must also be met for the landing configuration with-- (1) Maximum available takeoff power initially on each engine; (2) The airplane trimmed for an approach, with all engines operating, at VREF, at an approach gradient equal to the steepest used in the landing distance demonstration of Sec. 23.75; (3) Flaps in the landing position; (4) Landing gear extended; and (5) All propeller controls in the position recommended for approach with all engines operating. (d) A minimum speed to intentionally render the critical engine inoperative must be established and designated as the safe, intentional, one-engine- inoperative speed, VSSE. (e) At VMC, the rudder pedal force required to maintain control must not exceed 150 pounds and it must not be necessary to reduce power of the operative engine(s). During the maneuver, the airplane must not assume any dangerous attitude and it must be possible to prevent a heading change of more than 20 degrees. (f) At the option of the applicant, to comply with the requirements of Sec. 23.51(c)(1), VMCG may be determined. VMCG is the minimum control speed on the ground, and is the calibrated airspeed during the takeoff run at which, when the critical engine is suddenly made inoperative, it is possible to maintain control of the airplane using the rudder control alone (without the use of nosewheel steering), as limited by 150 pounds of force, and using the lateral control to the extent of keeping the wings level to enable the takeoff to be safely continued. In the determination of VMCG, assuming that the path of the airplane accelerating with all engines operating is along the centerline of the runway, its path from the point at which the critical engine is made inoperative to the point at which recovery to a direction parallel to the centerline is completed may not deviate more than 30 feet laterally from the centerline at any point. VMCG must be established with-- (1) The airplane in each takeoff configuration or, at the option of the applicant, in the most critical takeoff configuration; (2) Maximum available takeoff power on the operating engines; (3) The most unfavorable center of gravity; (4) The airplane trimmed for takeoff; and (5) The most unfavorable weight in the range of takeoff weights. [Amdt. 23-50, 61 FR 5188, Feb. 9, 1996] Sec. 23.151 Acrobatic maneuvers. Each acrobatic and utility category airplane must be able to perform safely the acrobatic maneuvers for which certification is requested. Safe entry speeds for these maneuvers must be determined. Sec. 23.153 Control during landings. It must be possible, while in the landing configuration, to safely complete a landing without exceeding the one-hand control force limits specified in Sec. 23.143(c) following an approach to land-- (a) At a speed of VREF minus 5 knots; (b) With the airplane in trim, or as nearly as possible in trim and without the trimming control being moved throughout the maneuver; (c) At an approach gradient equal to the steepest used in the landing distance demonstration of Sec. 23.75; and (d) With only those power changes, if any, that would be made when landing normally from an approach at VREF. [Amdt. 23-50, 61 FR 5189, Feb. 9, 1996] Sec. 23.155 Elevator control force in maneuvers. (a) The elevator control force needed to achieve the positive limit maneuvering load factor may not be less than: (1) For wheel controls, W/100 (where W is the maximum weight) or 20 pounds, whichever is greater, except that it need not be greater than 50 pounds; or (2) For stick controls, W/140 (where W is the maximum weight) or 15 pounds, whichever is greater, except that it need not be greater than 35 pounds. (b) The requirement of paragraph (a) of this section must be met at 75 percent of maximum continuous power for reciprocating engines, or the maximum continuous power for turbine engines, and with the wing flaps and landing gear retracted-- (1) In a turn, with the trim setting used for wings level flight at VO; and (2) In a turn with the trim setting used for the maximum wings level flight speed, except that the speed may not exceed VNE or VMO/MMO, whichever is appropriate. (c) Compliance with the requirements of this section may be demonstrated by measuring the normal acceleration that is achieved with the limiting stick force or by establishing the stick force per g gradient and extrapolating to the appropriate limit.(c)[d] There must be no excessive decrease in the gradient of the curve of stick force versus maneuvering load factor with increasing load factor. [Amdt. 23-14, 38 FR 31819, Nov. 19, 1973; 38 FR 32784, Nov. 28, 1973, as amended by Amdt. 23-45, 58 FR 42158, Aug. 6, 1993; Amdt. 23-50, 61 FR 5189, Feb. 9, 1996] Sec. 23.157 Rate of roll. (a) Takeoff. It must be possible, using a favorable combination of controls, to roll the airplane from a steady 30-degree banked turn through an angle of 60 degrees, so as to reverse the direction of the turn within: (1) For an airplane of 6,000 pounds or less maximum weight, 5 seconds from initiation of roll; and (2) For an airplane of over 6,000 pounds maximum weight, (W+500)/1,300 seconds, but not more than 10 seconds, where W is the weight in pounds. (b) The requirement of paragraph (a) of this section must be met when rolling the airplane in each direction with-- (1) Flaps in the takeoff position; (2) Landing gear retracted; (3) For a single-engine airplane, at maximum takeoff power; and for a multiengine airplane with the critical engine inoperative and the propeller in the minimum drag position, and the other engines at maximum takeoff power; and (4) The airplane trimmed at a speed equal to the greater of 1.2 VS1 or 1.1 VMC, or as nearly as possible in trim for straight flight. (c) Approach. It must be possible, using a favorable combination of controls, to roll the airplane from a steady 30-degree banked turn through an angle of 60 degrees, so as to reverse the direction of the turn within: (1) For an airplane of 6,000 pounds or less maximum weight, 4 seconds from initiation of roll; and (2) For an airplane of over 6,000 pounds maximum weight, (W+2,800)/2,200 seconds, but not more than 7 seconds, where W is the weight in pounds. (d) The requirement of paragraph (c) of this section must be met when rolling the airplane in each direction in the following conditions-- (1) Flaps in the landing position(s); (2) Landing gear extended; (3) All engines operating at the power for a 3 degree approach; and (4) The airplane trimmed at VREF. [Amdt. 23-14, 38 FR 31819, Nov. 19, 1973, as amended by Amdt. No. 23-45, 58 FR 42158, Aug. 6, 1993; Amdt. 23-50, 61 FR 5189, Feb. 9, 1996] |
|
|
(a) General. Each airplane must meet the trim requirements of this section after being trimmed and without further pressure upon, or movement of, the primary controls or their corresponding trim controls by the pilot or the automatic pilot. In addition, it must be possible, in other conditions of loading, configuration, speed and power to ensure that the pilot will not be unduly fatigued or distracted by the need to apply residual control forces exceeding those for prolonged application of Sec. 23.143(c). This applies in normal operation of the airplane and, if applicable, to those conditions associated with the failure of one engine for which performance characteristics are established. (b) Lateral and directional trim. The airplane must maintain lateral and directional trim in level flight with the landing gear and wing flaps retracted as follows: (1) For normal, utility, and acrobatic category airplanes, at a speed of 0.9 VH, VC, or VMO/MO, whichever is lowest; and (2) For commuter category airplanes, at all speeds from 1.4 VS1 to the lesser of VH or VMO/MMO. (c) Longitudinal trim. The airplane must maintain longitudinal trim under each of the following conditions: (1) A climb with-- (i) Takeoff power, landing gear retracted, wing flaps in the takeoff position(s), at the speeds used in determining the climb performance required by Sec. 23.65; and (ii) Maximum continuous power at the speeds and in the configuration used in determining the climb performance required by Sec. 23.69(a). (2) Level flight at all speeds from the lesser of VH and either VNO or VMO/ MMO (as appropriate), to 1.4 VS1, with the landing gear and flaps retracted. (3) A descent at VNO or VMO/MMO, whichever is applicable, with power off and with the landing gear and flaps retracted. (4) Approach with landing gear extended and with-- (i) A 3 degree angle of descent, with flaps retracted and at a speed of 1.4 VS1; (ii) A 3 degree angle of descent, flaps in the landing position(s) at VREF; and (iii) An approach gradient equal to the steepest used in the landing distance demonstrations of Sec. 23.75, flaps in the landing position(s) at VREF. (d) In addition, each multiple airplane must maintain longitudinal and directional trim, and the lateral control force must not exceed 5 pounds at the speed used in complying with Sec. 23.67(a), (b)(2), or (c)(3), as appropriate, with-- (1) The critical engine inoperative, and if applicable, its propeller in the minimum drag position; (2) The remaining engines at maximum continuous power; (3) The landing gear retracted; (4) Wing flaps retracted; and (5) An angle of bank of not more than five degrees. (e) In addition, each commuter category airplane for which, in the determination of the takeoff path in accordance with Sec. 23.57, the climb in the takeoff configuration at V2 extends beyond 400 feet above the takeoff surface, it must be possible to reduce the longitudinal and lateral control forces to 10 pounds and 5 pounds, respectively, and the directional control force must not exceed 50 pounds at V2 with-- (1) The critical engine inoperative and its propeller in the minimum drag position; (2) The remaining engine(s) at takeoff power; (3) Landing gear retracted; (4) Wing flaps in the takeoff position(s); and (5) An angle of bank not exceeding 5 degrees. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964, as
amended by Amdt. 23-21, 43 FR 2318, Jan. 16, 1978; Amdt.
23-34, 52 FR 1828, Jan. 15, 1987; Amdt. 23-42, 56 FR 351,
Jan. 3, 1991; 56 FR 5455, Feb. 11, 1991; Amdt. 23-50, 61 FR
5189, Feb. 9, 1996] |
|
|
The airplane must be longitudinally, directionally, and laterally stable under Secs. 23.173 through 23.181. In addition, the airplane must show suitable stability and control "feel" (static stability) in any condition normally encountered in service, if flight tests show it is necessary for safe operation. Sec. 23.173 Static longitudinal stability. Under the conditions specified in Sec. 23.175 and with the airplane trimmed as indicated, the characteristics of the elevator control forces and the friction within the control system must be as follows: (a) A pull must be required to obtain and maintain speeds below the specified trim speed and a push required to obtain and maintain speeds above the specified trim speed. This must be shown at any speed that can be obtained, except that speeds requiring a control force in excess of 40 pounds or speeds above the maximum allowable speed or below the minimum speed for steady unstalled flight, need not be considered. (b) The airspeed must return to within the tolerances specified for applicable categories of airplanes when the control force is slowly released at any speed within the speed range specified in paragraph (a) of this section. The applicable tolerances are-- (1) The airspeed must return to within plus or minus 10 percent of the original trim airspeed; and (2) For commuter category airplanes, the airspeed must return to within plus or minus 7.5 percent of the original trim airspeed for the cruising condition specified in Sec. 23.175(b). (c) The stick force must vary with speed so that any substantial speed change results in a stick force clearly perceptible to the pilot. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964, as amended by Amdt. 23-14, 38 FR 31820 Nov. 19, 1973; Amdt. 23-34, 52 FR 1828, Jan. 15, 1987] Sec. 23.175 Demonstration of static longitudinal stability. Static longitudinal stability must be shown as follows: (a) Climb. The stick force curve must have a stable slope at speeds between 85 and 115 percent of the trim speed, with-- (1) Flaps retracted; (2) Landing gear retracted; (3) Maximum continuous power; and (4) The airplane trimmed at the speed used in determining the climb performance required by Sec. 23.69(a). (b) Cruise. With flaps and landing gear retracted and the airplane in trim with power for level flight at representative cruising speeds at high and low altitudes, including speeds up to VNO or VMO/MMO, as appropriate, except that the speed need not exceed VH-- (1) For normal, utility, and acrobatic category airplanes, the stick force curve must have a stable slope at all speeds within a range that is the greater of 15 percent of the trim speed plus the resulting free return speed range, or 40 knots plus the resulting free return speed range, above and below the trim speed, except that the slope need not be stable-- (i) At speeds less than 1.3 VS1; or (ii) For airplanes with VNE established under Sec. 23.1505(a), at speeds greater than VNE; or (iii) For airplanes with VMO/MMO established under Sec. 23.1505(c), at speeds greater than VFC/MFC. (2) For commuter category airplanes, the stick force curve must have a stable slope at all speeds within a range of 50 knots plus the resulting free return speed range, above and below the trim speed, except that the slope need not be stable-- (i) At speeds less than 1.4 VS1; or (ii) At speeds greater than VFC/MFC; or (iii) At speeds that require a stick force greater than 50 pounds. (c) Landing. The stick force curve must have a stable slope at speeds between 1.1 VS1 and 1.8 VS1 with-- (1) Flaps in the landing position; (2) Landing gear extended; and (3) The airplane trimmed at-- (i) VREF, or the minimum trim speed if higher, with power off; and (ii) VREF with enough power to maintain a 3 degree angle of descent. [Amdt. 23-50, 61 FR 5190, Feb. 9, 1996] Sec. 23.177 Static directional and lateral stability. (a) The static directional stability, as shown by the tendency to recover from a wings level sideslip with the rudder free, must be positive for any landing gear and flap position appropriate to the takeoff, climb, cruise, approach, and landing configurations. This must be shown with symmetrical power up to maximum continuous power, and at speeds from 1.2 VS1 up to the maximum allowable speed for the condition being investigated. The angel of sideslip for these tests must be appropriate to the type of airplane. At larger angles of sideslip, up to that at which full rudder is used or a control force limit in Sec. 23.143 is reached, whichever occurs first, and at speeds from 1.2 VS1 to VO, the rudder pedal force must not reverse. (b) The static lateral stability, as shown by the tendency to raise the low wing in a sideslip, must be positive for all landing gear and flap positions. This must be shown with symmetrical power up to 75 percent of maximum continuous power at speeds above 1.2 VS1 in the take off configuration(s) and at speeds above 1.3 VS1 in other configurations, up to the maximum allowable speed for the configuration being investigated, in the takeoff, climb, cruise, and approach configurations. For the landing configuration, the power must be that necessary to maintain a 3 degree angle of descent in coordinated flight. The static lateral stability must not be negative at 1.2 VS1 in the takeoff configuration, or at 1.3 VS1 in other configurations. The angle of sideslip for these tests must be appropriate to the type of airplane, but in no case may the constant heading sideslip angle be less than that obtainable with a 10 degree bank, or if less, the maximum bank angle obtainable with full rudder deflection or 150 pound rudder force. (c) Paragraph (b) of this section does not apply to acrobatic category airplanes certificated for inverted flight. (d) In straight, steady slips at 1.2 VS1 for any landing gear and flap positions, and for any symmetrical power conditions up to 50 percent of maximum continuous power, the aileron and rudder control movements and forces must increase steadily, but not necessarily in constant proportion, as the angle of sideslip is increased up to the maximum appropriate to the type of airplane. At larger slip angles, up to the angle at which full rudder or aileron control is used or a control force limit contained in Sec. 23.143 is reached, the aileron and rudder control movements and forces must not reverse as the angle of sideslip is increased. Rapid entry into, and recovery from, a maximum sideslip considered appropriate for the airplane must not result in uncontrollable flight characteristics. [Amdt. 23-50, 61 FR 5190, Feb. 9, 1996] Sec. 23.179 [Removed. Amdt. No. 23-45, 58 FR 42158, Aug. 6, 1993] Sec. 23.181 Dynamic stability. (a) Any short period oscillation not including combined lateral-directional oscillations occurring between the stalling speed and the maximum allowable speed appropriate to the configuration of the airplane must be heavily damped with the primary controls-- (1) Free; and (2) In a fixed position. (b) Any combined lateral-directional oscillations ("Dutch roll") occurring between the stalling speed and the maximum allowable speed appropriate to the configuration of the airplane must be damped to 1/10 amplitude in 7 cycles with the primary controls-- (1) Free; and (2) In a fixed position. (c) If it is determined that the function of a stability augmentation system, reference Sec. 23.672, is needed to meet the flight characteristic requirements of this part, the primary control requirements of paragraphs (a)(2) and (b)(2) of this section are not applicable to the tests needed to verify the acceptability of that system. (d) During the conditions as specified in Sec. 23.175, when the longitudinal control force required to maintain speeds differing from the trim speed by at least plus and minus 15 percent is suddenly released, the response of the airplane must not exhibit any dangerous characteristics nor be excessive in relation to the magnitude of the control force released. Any long-period oscillation of flight path, phugoid oscillation, that results must not be so unstable as to increase the pilot's workload or otherwise endanger the airplane. [Amdt. 23-21, 43 FR 2318, Jan. 16, 1978, as amended by Amdt. No. 23-45, 58 FR 42158, Aug. 6, 1993] |
|
|
(a) It must be possible to produce and to correct roll by unreversed use of the rolling control and to produce and to correct yaw by unreversed use of the directional control, up to the time the airplane stalls. (b) The wings level stall characteristics must be demonstrated in flight as follows. Starting from a speed at least 10 knots above the stall speed, the elevator control must be pulled back so that the rate of speed reduction will not exceed one knot per second until a stall is produced, as shown by either: (1) An uncontrollable downward pitching motion of the airplane; (2) A downward pitching motion of the airplane that results from the activation of a stall avoidance device (for example, stick pusher); or (3) The control reaching the stop. (c) Normal use of elevator control for recovery is allowed after the downward pitching motion of paragraphs (b)(1) or (b)(2) of this section has unmistakably been produced, or after the control has been held against the stop for not less than the longer of two seconds or the time employed in the minimum steady slight speed determination of Sec. 23.49. (d) During the entry into and the recovery from the maneuver, it must be possible to prevent more than 15 degrees of roll or yaw by the normal use of controls. (e) Compliance with the requirements of this section must be shown under the following conditions: (1) Wing flaps. Retracted, fully extended, and each intermediate normal operating position. (2) Landing gear. Retracted and extended. (3) Cowl flaps. Appropriate to configuration. (4) Power: (i) Power off; and (ii) 75 percent of maximum continuous power. However, if the power-to- weight ratio at 75 percent of maximum continuous power result in extreme nose-up attitudes, the test may be carried out with the power required for level flight in the landing configuration at maximum landing weight and a speed of 1.4 VSO, except that the power may not be less than 50 percent of maximum continuous power. (5) Trim. The airplane trimmed at a speed as near 1.5 VS1 as practicable. (6) Propeller. Full increase r.p.m. position for the power off condition. [Amdt. 23-50, 61 FR 5191, Feb. 9, 1996] Sec. 23.203 Turning flight and accelerated turning stalls. Turning flight and accelerated turning stalls must be demonstrated in tests as follows: (a) Establish and maintain a coordinated turn in a 30 degree bank. Reduce speed by steadily and progressively tightening the turn with the elevator until the airplane is stalled, as defined in Sec. 23.201(b). The rate of speed reduction must be constant, and-- (1) For a turning flight stall, may not exceed one knot per second; and (2) For an accelerated turning stall, be 3 to 5 knots per second with steadily increasing normal acceleration. (b) After the airplane has stalled, as defined in Sec. 23.201(b), it must be possible to regain wings level flight by normal use of the flight controls, but without increasing power and without-- (1) Excessive loss of altitude; (2) Undue pitchup; (3) Uncontrollable tendency to spin; (4) Exceeding a bank angle of 60 degrees in the original direction of the turn or 30 degrees in the opposite direction in the case of turning flight stalls; (5) Exceeding a bank angle of 90 degrees in the original direction of the turn or 60 degrees in the opposite direction in the case of accelerated turning stalls; and (6) Exceeding the maximum permissible speed or allowable limit load factor. (c) Compliance with the requirements of this section must be shown under the following conditions: (1) Wing flaps: Retracted, fully extended, and each intermediate normal operating position; (2) Landing gear: Retracted and extended; (3) Cowl flaps: Appropriate to configuration; (4) Power: (i) Power off; and (ii) 75 percent of maximum continuous power. However, if the power-to- weight ratio at 75 percent of maximum continuous power results in extreme nose-up attitudes, the test may be carried out with the power required for level flight in the landing configuration at maximum landing weight and a speed of 1.4 VSO, except that the power may not be less than 50 percent of maximum continuous power. (5) Trim: The airplane trimmed at a speed as near 1.5 VS1 as practicable. (6) Propeller. Full increase rpm position for the power off condition. [Amdt. 23-14, 38 FR 31820, Nov. 19, 1973, as amended by Amdt. No. 23-45, 58 FR 42159, Aug. 6, 1993; Amdt. 23-50, 61 FR 5191, Feb. 9, 1996] Sec. 23.205 [Removed. Amdt. 23-50, 61 FR 5191, Feb. 9, 1996] Sec. 23.207 Stall warning. (a) There must be a clear and distinctive stall warning, with the flaps and landing gear in any normal position, in straight and turning flight. (b) The stall warning may be furnished either through the inherent aerodynamic qualities of the airplane or by a device that will give clearly distinguishable indications under expected conditions of flight. However, a visual stall warning device that requires the attention of the crew within the cockpit is not acceptable by itself. (c) During the stall tests required by Sec. 23.201(b) and Sec. 23.203(a)(1), the stall warning must begin at a speed exceeding the stalling speed by a margin of not less than 5 knots and must continue until the stall occurs. (d) When following procedures furnished in accordance with Sec. 23.1585, the stall warning must not occur during a takeoff with all engines operating, a takeoff continued with one engine inoperative, or during an approach to landing. (e) During the stall tests required by Sec. 23.203(a)(2), the stall warning must begin sufficiently in advance of the stall for the stall to be averted by pilot action taken after the stall warning first occurs. (f) For acrobatic category airplanes, an artificial stall warning may be mutable, provided that it is armed automatically during takeoff and rearmed automatically in the approach configuration. [Amdt. 23-7, 34 FR 13087, Aug. 13, 1969, as amended by Amdt. 23-45, 58 FR 42159, Aug. 6, 1993; Amdt. 23-50, 61 FR 5191, Feb. 9, 1996] |
|
|
(a) Normal category airplanes. A single-engine, normal category airplane must be able to recover from a one-turn spin or a three-second spin, whichever takes longer, in not more than one additional turn after initiation of the first control action for recovery, or demonstrate compliance with the optional spin resistant requirements of this section. (1) The following apply to one turn or three second spins: (i) For both the flaps-retracted and flaps-extended conditions, the applicable airspeed limit and positive limit maneuvering load factor must not be exceeded; (ii) No control forces or characteristic encountered during the spin or recovery may adversely affect prompt recovery; (iii) It must be impossible to obtain unrecoverable spins with any use of the flight or engine power controls either at the entry into or during the spin; and (iv) For the flaps-extended condition, the flaps may be retracted during the recovery but not before rotation has ceased. (2) At the applicant's option, the airplane may be demonstrated to be spin resistant by the following: (i) During the stall maneuver contained in Sec. 23.201, the pitch control must be pulled back and held against the stop. Then, using ailerons and rudders in the proper direction, it must be possible to maintain wings-level flight within 15 degrees of bank and to roll the airplane from a 30 degree bank in one direction to a 30 degree bank in the other direction; (ii) Reduce the airplane speed using pitch control at a rate of approximately one knot per second until the pitch control reaches the stop; then, with the pitch control pulled back and held against the stop, apply full rudder control in a manner to promote spin entry for a period of seven seconds or through a 360 degree heading change, whichever occurs first. If the 360 degree heading change is reached first, it must have taken no fewer than four seconds. This maneuver must be performed first with the ailerons in the neutral position, and then with the ailerons deflected opposite the direction of turn in the most adverse manner. Power and airplane configuration must be set in accordance with Sec. 23.201(e) without change during the maneuver. At the end of seven seconds or a 360 degree heading change, the airplane must respond immediately and normally to primary flight controls applied to regain coordinated, unstalled flight without reversal of control effect and without exceeding the temporary control forces specified by Sec. 23.143(c); and (iii) Compliance with Secs. 23.201 and 23.203 must be demonstrated with the airplane in uncoordinated flight, corresponding to one ball width displacement on a slip-skid indicator, unless one ball width displacement cannot be obtained with full rudder, in which case the demonstration must be with full rudder applied. (b) Utility category airplanes. A utility category airplane must meet the requirements of paragraph (a) of this section. In addition, the requirements of paragraph (c) of this section and Sec. 23.807(b)(7) must be met if approval for spinning is requested. (c) Acrobatic category airplanes. An acrobatic category airplane must meet the spin requirements of paragraph (a) of this section and Sec. 23.807(b)(6). In addition, the following requirements must be met in each configuration for which approval for spinning is requested: (1) The airplane must recover from any point in a spin up to and including six turns, or any greater number of turns for which certification is requested, in not more than one and one-half additional turns after initiation of the first control action for recovery. However, beyond three turns, the spin may be discontinued if spiral characteristics appear. (2) The applicable airspeed limits and limit maneuvering load factors must not be exceeded. For flaps-extended configurations for which approval is requested, the flaps must not be retracted during the recovery. (3) It must be impossible to obtain unrecoverable spins with any use of the flight or engine power controls either at the entry into or during the spin. (4) There must be no characteristics during the spin (such as excessive rates of rotation or extreme oscillatory motion) that might prevent a successful recovery due to disorientation or incapacitation of the pilot. [Amdt. 23-50, 61 FR 5191, Feb. 9, 1996] |
|
|
(a) A landplane may have no uncontrollable tendency to nose over in any reasonably expected operating condition, including rebound during landing or takeoff. Wheel brakes must operate smoothly and may not induce any undue tendency to nose over. (b) A seaplane or amphibian may not have dangerous or uncontrollable porpoising characteristics at any normal operating speed on the water. Sec. 23.233 Directional stability and control. (a) A 90 degree cross-component of wind velocity, demonstrated to be safe for taxiing, takeoff, and landing must be established and must be not less than 0.2 VSO. (b) The airplane must be satisfactorily controllable in power-off landings at normal landing speed, without using brakes or engine power to maintain a straight path until the speed has decreased to at least 50 percent of the speed at touchdown. (c) The airplane must have adequate directional control during taxiing. (d) Seaplanes must demonstrate satisfactory directional stability and control for water operations up to the maximum wind velocity specified in paragraph (a) of this section. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964; 30 FR 258, Jan. 9, 1965, as amended by Amdt. No. 23-45, 58 FR 42159, Aug. 6, 1993; Amdt. 23-50, 61 FR 5192, Feb. 9, 1996] Sec. 23.235 Operation on unpaved surfaces. The airplane must be demonstrated to have satisfactory characteristics and the shock-absorbing mechanism must not damage the structure of the airplane when the airplane is taxied on the roughest ground that may reasonably be expected in normal operation and when takeoffs and landings are performed on unpaved runways having the roughest surface that may reasonably be expected in normal operation. [Amdt. 23-50, 61 FR 5192, Feb. 9, 1996] Sec. 23.237 Operation on water. A wave height, demonstrated to be safe for operation, and any necessary water handling procedures for seaplanes and amphibians must be established. [Amdt. 23-50, 61 FR 5192, Feb. 9, 1996] Sec. 23.239 Spray characteristics. Spray may not dangerously obscure the vision of the
pilots or damage the propellers or other parts of a seaplane
or amphibian at any time during taxiing, takeoff, and
landing. |
|
|
There must be no vibration or buffeting severe enough to result in structural damage, and each part of the airplane must be free from excessive vibration, under any appropriate speed and power conditions up to VD/MD. In addition, there must be no buffeting in any normal flight condition severe enough to interfere with the satisfactory control of the airplane or cause excessive fatigue to the flight crew. Stall warning buffeting within these limits is allowable. [Amdt. No. 23-45, 58 FR 42159, Aug. 6, 1993] Sec. 23.253 High speed characteristics. If a maximum operating speed VMO/MMO is established under Sec. 23.1505(c), the following speed increase and recovery characteristics must be met: (a) Operating conditions and characteristics likely to cause inadvertent speed increases (including upsets in pitch and roll) must be simulated with the airplane trimmed at any likely speed up to VMO/MMO. These conditions and characteristics include gust upsets, inadvertent control movements, low stick force gradients in relation to control friction, passenger movement, leveling off from climb, and descent from Mach to airspeed limit altitude. (b) Allowing for pilot reaction time after occurrence of the effective inherent or artificial speed warning specified in Sec. 23.1303, it must be shown that the airplane can be recovered to a normal attitude and its speed reduced to VMO/MMO, without-- (1) Exceeding VD/MD, the maximum speed shown under Sec. 23.251, or the structural limitations; or (2) Buffeting that would impair the pilot's ability to read the instruments or to control the airplane for recovery. (c) There may be no control reversal about any axis at any speed up to the maximum speed shown under Sec. 23.251. Any reversal of elevator control force or tendency of the airplane to pitch, roll, or yaw must be mild and readily controllable, using normal piloting techniques. [Amdt. 23-7, 34 FR 13087, Aug. 13, 1969; as amended
by Amdt. 23-26, 45 FR 60170, Sept. 11, 1980; Amdt. No.
23-45, 58 FR 42160, Aug. 6, 1993; Amdt. 23-50, 61 FR 5192,
Feb. 9, 1996] |
|
|
For more information on how ASTECH Engineering may be able to help you, please contact Jeff Wilson at astech@cox.net or call 316-304-6157. © Copyright 1996 ASTECH Engineering. All rights reserved. No part of this document may be reproduced in any form without the expressed written consent of the author. |
